Auralex EZ-Stick Pro Tabs - Manual

Auralex ® Studiofoam ® / User Guide
1-800-959-3343 / 317-842-2600
9955 Westpoint Drive, Suite 101, Indianapolis IN USA 46256
1150-309.Studiofoam User Guide.indd (10/07/2013 - 11:17 AM)
EZ-Stick Pro ™
Clean attachment points on the wall surface with Isopropyl alcohol (avoid household cleaners), wipe gently and let
dry. Separate the
EZ-Stick Pro Tabs from each other. Remove one of the paper release liners from the strip. Apply
the tabs on the rear of the panel near the outside edges, orient vertically for maximum holding strength. Remove
the second paper release liner from the backside of the tab, position the panel with the target location on the wall
and press firmly to attach. Use 4 tabs for a 2’ x 2’
Studiofoam panel and 6 tabs for a 2’ x 4’ panel.
Tubetak Pro ™ Liquid Adhesive & Foamtak ™ Spray Adhesive
Both are contact adhesives, so wait a period of time (see below) after applying it to the back of the panel before
trying to adhere the panel to the wall.
•
Tubetak Pro (caulk gun required) typically works better if it is spread thin, use a putty knife if needed.
Refer to the application diagrams to the right. If the adhesive seems to take a while to dry (cure time can be
dependent on humidity and other environmental factors), you may consider supporting the panel in place
with a T-pin or finish nail.
• If you are using Foamtak (US only), hold the can 12 to 18” away from the Studiofoam and shake the can
from side to side to yield a spider web pattern. For best results apply to both surfaces, allow 45 seconds to
tack and then apply. For a more temporary bond apply the
Foamtak to one surface only. Store the Foamtak
upside down between applications may allow a more consistent spray pattern. You can use the Studiofoam
carton as spray shields for a cleaner installation. Stacking two Studiofoam cartons can be used as a
convenient work surface.
TEMP•Tabs ™
TEMP•Tabs are a semi-permanent mounting kit that is a great way to temporarily install your Studiofoam.
Removing the tabs causes some minimal damage to walls that may require spot repairs.
Other Mounting Options
• T-Pins or Finish Nails can be used to tack the panels in place for a quick installation with minimal wall
damage. Sometimes larger nails or panel movement can cause the foam to tear, so this is usually best
as a temporary installation method.
• Studiofoam can be mounted to a backing (such as pegboard, Corex, cardboard, plastic, plywood, etc)
before installing it on a wall. The assembly allows for added durability when relocating/repurposing
Studiofoam panels.
NOTES:
• EZ-Stick Pro Tabs may not adhere well to some vinyl wallpapers. Apply to surfaces above 50˚ F (10˚ C).
Adhesive could soften and lose adhesion above 105˚ F (40˚ C).
EZ-Stick Pro Tabs are considered
permanent and will damage the wall surface when removed.
• Both Tubetak Pro and Foamtak are considered permanent installations. Removing a panel after the
adhesive has cured can result in some damage to the Studiofoam and the mounting surface. Auralex is
not responsible for any damage to walls, floors, ceiling or the overall structure that occurs doing installation
or removal of our products. Try using a flat edge knife to carefully scrape the panel away from the wall to
minimize tearing, and then use a citrus-based adhesive remover.
Thank you for purchasing Auralex ® Studiofoam ® high performance acoustical absorption treatment that can easily be mounted to walls & ceilings.
• Prior to mounting, mark desired panel locations on the wall with small pencil marks or masking tape.
• If you need to cut your Studiofoam, it is recommended to use a straightedge and an electric carving knife. Don’t force the knife; let the blades do the work.
EZ-Stick Pro ™ Tabs shown
Application of Auralex ® Foamtak ™ shown
Auralex ® TEMP•Tabs ™ Shown
Typical Tubetak ™
application pattern
Tubetak ™ application
for difficult to adhere
to surfaces