Waterworks Easton Vintage Gooseneck Three Hole Deck Mounted Lavatory Faucet with Porcelain Lever Handles - Manual

Installation Guidelines
W A T E R W O R K S
Easton Gooseneck Lavatory Faucet
These guidelines have been prepared for the professional contractor to aid in the installation of:
EASTON GOOSENECK LAVATORY FAUCET (EALS31, 32-K, 33-K, 34-K, 35-K, 51,
52-K, 53-K, 54-K, 55-K) All dimensions are based on original specification and are subject to
change and variation. Please consult your Design Associate for current specifications.
EALS31 (cross handles)
EALS32-K (metal lever handles)
EALS33-K (white porcelain lever handles)
EALS34-K (black porcelain lever handles)
EALS35-K (oak lever handles)
6"
2 3
8
"
6 3
8
"
2 7
16
"
EALS32-K EALS33-K, 34-K, 35-K
3 5
8
" 3 5
8
"
2 3
8
" 2 3
8
"
3" 3 3
8
"
IMPORTANT
To ensure this product is installed properly,
you must read and follow these guidelines.
The owner/user of the faucet must keep
this information for future reference.
3 5
8
"
2 3
8
"
This faucet must be on-site prior to rough in and
allows the installer to visualize the installation and
match the 8" center spread
EALS51
EALS52-K (metal lever handles)
EALS53-K (white porcelain lever handles)
EALS54-K (black porcelain lever handles)
EALS55-K (oak lever handles)
EALS52-K EALS53-K, 54-K, 55-K
3 1
2
"
3 3
8
"
3 1
2
"
3"
2 3
8
" 2 3
8
"
EALS51
3 1
2
"
2 3
8
"
(cross handles)
CLASSIC
VINTAGE
Check countertop and sink measurements to assure
the spout projects far enough into the sink.
Inspect this product to assure you have all parts
required for proper installation.
Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
Do NOT use putty during this installation.
SIDE VALVE INSTALLATION
1. With the lock nut (4b) and upper sealing gasket (4a)
installed on the side valve (5-7), insert the side valve
into the hole in the mounting surface so at least ½"
of threads are exposed.
2. Place the upper sealing gasket (4) onto the side
valve then thread the base escutcheon (3) onto the
side valve.
3. Thread the handle assembly (1-1h) onto the side
valve until it stops. Hand tight is adequate; if this
assembly is too tight, the handle will bind.
4. Unthread the base escutcheon until it contacts the
gland nut (1e) which will assure proper side valve
height.
5. Tighten the lock nut up against the underside of the
mounting surface to secure the side valve
6. Repeat these steps to install the second side valve.
SPOUT AND DRAIN INSTALLATION
7. Unthread and remove the spout nut (10), rubber
spout washer (10A), tee assembly (9-9b) and tee
washer (9c) from the spout shank.
8. Insert the spout assembly (10b,11-13) through the
spout hole of the mounting surface, reinstall the
rubber spout washer then tighten the spout
mounting nut to secure the spout to the mounting
surface.
Refer to the specification and assembly drawings
attached. Faucet is sold partially assembled but
shown fully disassembled for illustrative and service
purposes only.
Be sure your installation conforms to local codes.
Waterworks is a registered trademark of Waterworks Inc. 07.14.06