Waterworks Easton Classic Two Hole Bridge Gooseneck Kitchen Faucet, Oak Lever Handles and Spray - Manual (Page 2)

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
EASTON CLASSIC
Two Hole Bridge Kitchen Faucet and Spray
INSTALLATION GUIDELINES
Page 2 of 2 9.16.2014
These guidelines have been prepared for the professional contractor to aid in the installation of:
EASTON TWO HOLE KITCHEN FAUCET WITH SPRAY. STYLE NOS.
EAKM31, EAKM32, EAKM33, EAKM34, & EAKM35
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
12. Lastly attach the KNURLED END of the HOSE to the
CHECK VALVE HOUSING and attach the CONICAL
END of the HOSE to the SPRAY.
HOSE
KNURLED
END
NUT
RUBBER
WASHER
RUBBER
GASKET
SHANK
ESCUTCHEON
PLASTIC
INSERT
HOSE
CONICAL
END
RETAINING
COLLAR
SPRAY
HOSE
KNURLED
END
NUT
RUBBER
WASHER
RUBBER
GASKET
SHANK
ESCUTCHEON
PLASTIC
INSERT
HOSE
CONICAL
END
RETAINING
COLLAR
SPRAY
FIGURE - 03
¾ Note: HOSE is not shown complete.
INSPECT THE INSTALLATION:
13. Remove the flow restricting AERATOR by
unthreading the AERATOR HOUSING, then carefully
open the hot and cold valves to flush out any debris
in the supply lines. See Figure - 0 1.
14. Inspect all connections for leaks.
15. Re-install the flow restricting aerator.
¾ If further assistance is required, please contact
Product Support at 1-800-927-2120 (8am-6pm EST).
¾ See service part document for parts ordering,
available on WATERWORKS.COM.
* Putty contains oils and can cause permanent
discoloration on certain materials such as marble,
granite and any porous surface.
2. Remove the TEE by loosening the TEE NUT and
unthread the TEE from the SHANK.
3. Place the SPOUT ASSEMBLY through the holes on
the MOUNTING DECK, making sure the RUBBER
GASKETS are below the ESCUTCHEONS.
4. Reinstall the RUBBER WASHERS and NUTS to the
bottom of the SHANKS to secure the SPOUT
ASSEMBLY.
¾ See Figure 2. for Steps 5 & 6.
CHECK
VALVES
CHECK
VALVE
HOUSING
SHANK
TEE
(SECTION
VIEW)
COPPER
TUBE
O-RING
SPACER
TEE NUT
CHECK
VALVES
CHECK
VALVE
HOUSING
SHANK
TEE
(SECTION
VIEW)
COPPER
TUBE
O-RING
SPACER
TEE NUT
FIGURE - 02
5. Reinstall TEE by sliding it over the COPPER TUBE
and tighten to SHANK.
6. Re-install the O-RING, SPACER & tighten TEE NUT
to secure TEE to the SHANK.
SIDE SPRAY INSTALLATION:
¾ See Figure 3. for Steps 6-12.
7. Remove the NUT & RUBBER WASHER from bottom
of SHANK
8. Place ESCUTCHEON & SHANK through the
mounting hole, making sure the RUBBER GASKET is
below. Reinstall the NUT and RUBBER WASHER to
secure the spray return.
9. Drop the KNURLED END of the handshower HOSE
through the ESCUTCHEON and below the deck.
10. Spread the PLASTIC INSERT open and place the
HOSE into it. Snap the PLASTIC INSERT into the
ESCUTCHEON to make sure HOSE does not slip
below the deck.
11. Thread the RETAINING COLLAR onto the top of the
ESCUTCHEON.