Waterworks Odeon One Hole Low Profile Kitchen Faucet, Metal Lever Handles User Manual
Installation guidelines
Odeon
®
Kitchen Mixer with Pullout Sprayer
10/03
W A T E R W O R K S
®
These guidelines have been prepared for the professional contractor to aid in the installation of:
ODEON
®
KITCHEN MIXER WITH PULLOUT SPRAYER
(WWKM13)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
1
INSTALLATION GUIDELINES
These guidelines have been prepared for the professional contractor to
aid in installation. IIm
mp
poorrtta
an
ntt n
noottee:: This faucet is protected against back flow by a
certified double check valve system. One check valve is located at the inlet of the
sprayhead hose and one is located at the inlet of the sprayhead. These check valves
should not be removed.
➢ Use only a protected, smooth-jawed or strap wrench on any finished
surface.
➢ If possible, install the faucet assembly on the sink or mounting surface
before setting.
➢ Remove the barrel nut(7D), metal washer (7C) and rubber washer (7B)
from the base of the spout.
➢ Insert the supply hoses (4D) and spout shank through the mounting hole
on the sink. Secure the faucet body (6) using the barrel nut (7D) and
washers (7C+7B) provided (the barrel nut should only be hand-tightened
at this time). Do not use plumber's putty, upper and lower washers are
provided.The barrel nut (7D) will accommodate various deck thicknesses.
For standard thickness(1" or less), apply the barrel nut (7D) with the
unthreaded portion first.
➢ Check the spouts rotation to ensure that it rotates to the left and the right.
Now the barrel nut (7D) can be fully tightened.
➢ Feed the male threaded end of the spray hose (5B) into the faucet body
(3) until the sprayer (9) is fully seated.
➢ Connect the male threaded end of the spray hose (5B) to the check valve
assembly (10).Then connect the outlet hose (4C) to the other side of the
check valve assembly (10). Be sure to use the washers provided.
➢ Attach the weight (5C) to the hose (5B) on the spout side of the loop just
above the bend using the screws provided.
➢ Connect the supply hoses (4D) to the water supply valves (not supplied).
➢ Check that all connections are watertight.
➢ After installation, unscrew and remove the pullout sprayer (9) from the
spray hose (5B). With the spray hose (5B) in hand and positioned over the
sink move the faucet lever (1) to the full open position to flush out any
debris in the supply lines. Once the lines have been flushed, turn the faucet
off and reinstall the sprayer.
➢ If further assistance is required, please contact Product Support at:
1-800-927-2120 (8am-7pm EST).
OPERATION:
➢ Lift the handle (1) to operate the faucet. Raising the handle upward
increases the volume.
➢ Rotate to the left for hot water and to the right for cold water.
➢ Pressing the button on the top of the sprayer (9) changes the flow.The
normal flow is aerated and pressing the button changes it to a fine spray.
Once the faucet is turned off the sprayer reverts back to the normal flow.
WWKM13
16"
6
1
/
2
"
1
5
/
8
"
max
1
5
/
16
"
9
1
/
2
"
6
3
/
4
"
8
3
/
4
"
12
3
/
4
" (open)
10
7
/
8
" (closed)
10
1
/
2
"
Notes:
• Drill hole size: 1
3
/
8
"
• Flexible supply hose
connections:
3
/
8
" o.d.
compression
DOC. PRT.
DESCRIPTION
1
Lever
1A
Screw
1B
Button
2A
Cap
2B
Nut
2C
Cartridge
3
Body
3A
Plastic insert
4
Insert assy
4A
Insert
4C
Outlet hose
4D
Supply hose
5A
Rubber Washer
5B
Spray hose
5C
Weight
5D
Rubber washer
6
Inner body assy
6A
Inner body
6B
O'ring
7
Mounting nut assy
7A
O'ring
7B
Rubber washer
7C
Metal washer
7D
Barrel nut
8
Flow r. w/check v.
9
Pull out spray
9A
Aerator set
4
6
7
9
9A
5D
1A
1B
2
3
7D
7C
7B
7A
6B
6A
4B
4A
3B
5B
4D
4C
3A
2A
2B
2C
1
Rubber washer
Check valve housing
Rubber washer
10A
Check valve
10B
Check valve housing
10C
10D
10E
(upper)
(lower)
5C
5A
10
8
10A
10B
10C
10D
10E