Waterworks Aero Low Profile Concealed Tub Filler With Handshower and Metal Cross Handles User Manual
Installation guidelines, Aetu 88, Aetu 89
AETU 88
Inlets
3
⁄
4
" straight male thread
NPT adapters provided
10"-12"
2"
Note:
Drilling hole sizes:
Sidevalves and handshower: 1
1
⁄
2
"
Spout: 1
1
⁄
4
"
Must have access panel
for servicing
Consult your local building codes
for anti-scald requirements
2
5
⁄
8
"
2
5
⁄
8
"
2
1
⁄
2
"
4
1
4
"
9
1
⁄
4
"
3"
max.
2"
max.
2
3
⁄
4
"
1
3
⁄
4
"
max.
Flow restrictor/Non-return valve
2
7
⁄
16
"
2"
2
5
⁄
8
"
2
5
⁄
8
"
2
1
⁄
2
"
2
3
4
"
4
1
⁄
4
"
9
1
⁄
4
"
3"
max.
2"
max.
Inlets
3
⁄
4
" straight male thread
NPT adapters provided
10"-12"
Note:
Drilling hole sizes:
Sidevalves and handshower: 1
1
⁄
2
"
Spout: 1
1
⁄
4
"
Must have access panel
for servicing
Consult your local building codes
for anti-scald requirements
1
3
⁄
4
"
max.
Flow restrictor/Non-return valve
2
7
⁄
16
"
AETU 89
Installation Guidelines
INSTALLATION GUIDELINES
➢
Use only a protected, smooth-jawed, or strap wrench on any finished surface.
➢
For proper installation, the deck surface should be installed prior to
mounting the mixer.
➢
It is recommended that an access panel be provided for future service.
➢
Check the specifications (left) for drilling hole sizes and suggested centers.
➢
Run
3
⁄
4
" supply lines for maximum water flow.
➢
Accessible shut-off valves, which will facilitate servicing, are recommended
for the hot and cold feed lines.
➢
To remove the trim from the valve body, loosen and remove the handle
screw.The cover and escutcheon should be hand tight.
➢
DO NOT use putty on deck fittings. Upper and lower washers are provided.
➢
When you screw the escutcheon onto the deck valve body, expose
several threads above it. Next, screw the valve cover down until it seats.
Then move the escutcheon up until it loosely meets the bottom of the
cover. Finally, tighten the bottom lock nut to secure the valve to the deck.
➢
Once the spout is securely mounted, install the flexible hoses between the
spout and valve bodies using the gaskets provided.
➢
Be sure the cone-shaped end of the hose is attached to the handshower.
To pull hose end through escutcheon, unscrew finish cover from escutcheon
and remove plastic guide; pull hose through and reassemble.
➢
Connect the hand-shower hose to the “T” assembly at the base
of the spout.
➢
After installation, unscrew and remove the aerator assembly. Carefully open
the hot and cold valves fully to flush out any debris in the supply lines. Once
the lines have been flushed, close the valves and reinstall the aerator assembly.
➢ IMPORTANT:
It is necessary to check for leaks and proper function of
mixer prior to being enclosed.
➢
If further assistance is required, please contact Product Support at
1-800-927-2120 (8am–7pm EST).
Aero Concealed Tub Filler with Handshower
5/03
These guidelines have been prepared for the professional contractor to aid in the installation of:
AERO CONCEALED TUB FILLER WITH HANDSHOWER (AETU 88/89)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.