Waterworks Easton Classic Low Profile Concealed Tub Filler With Handshower and White Porcelain Lever Handles - Manual

2 3 / 8 "
3"
5"
1 5 / 8 "
max
2"
max
3 3 / 4 "
3"
max
6"
10"
8 1 / 2 "
2 1 /
4
"
24" hose
78" hose
3 /
4
" NPT
3 1 / 2 "
3 3 / 4 "
Ш 2 3 / 8 "
3 1 / 2 "
3 3 / 4 "
Ш 2 3 / 8 "
EATU02-K EATU03-K, 04-K, 05K
Notes:
• Inlets are 3 / 4 " straight
male thread - NPT
adaptors provided
• Drilling hole size: 1 1 /
2
"
• Must have access panel
for servicing.
• Consult your local
building codes for
anti-scald requirements.
Easton ® Concealed Tub Filler with Hand Shower - Covered
These guidelines have been prepared for the professional contractor to aid in the installation of:
EASTON
® CONCEALED TUB FILLER WITH HAND SHOWER (COVERED)
(EATU01, 02-K, 03-K, 04-K, 05-K)
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.
Installation Guidelines
1
W A T E R W O R K S ®
12/24
COVERED
EATU01 (CROSS HANDLE)
EATU02-K (METAL LEVER HANDLE)
EATU03-K (WHITE PORCELAIN LEVER HANDLE)
EATU04-K (BLACK PORCELAIN LEVER HANDLE)
EATU05-K (OAK LEVER HANDLE)
INSTALLATION GUIDELINES:
IMPORTANT:
➢
➢ T To o e en nssu urre e tth hiiss p prro od du ucctt iiss iin nssttaalllle ed d p prro op pe errllyy,, yyo ou u m mu usstt rre eaad d aan nd d
ffo ollllo ow w tth he esse e ggu uiid de elliin ne ess..
➢ ➢ T Th he e o ow wn ne err//u usse err o off tth he e ffaau ucce ett m mu usstt kke ee ep p tth hiiss iin nffo orrm maattiio on n ffo orr
ffu uttu urre e rre effe erre en ncce e..
➢ ➢ B Be e ssu urre e yyo ou urr iin nssttaallllaattiio on n cco on nffo orrm mss tto o llo occaall cco od de ess.. IItt iiss tth he e
rre essp po on nssiib biilliittyy o off tth he e p pllu um mb be err tto o p prro ovviid de e aan nttii--ssccaalld d p prro otte eccttiio on n..
➢ ➢ A Acccce essssiib blle e ssh hu utt--o offff vvaallvve ess,, w wh hiicch h w wiillll ffaacciilliittaatte e sse errvviicciin ngg,, aarre e
rre ecco om mm me en nd de ed d ffo orr tth he e h ho ott aan nd d cco olld d ffe ee ed d lliin ne ess..
➢ ➢ A An n aacccce essss p paan ne ell iiss n ne ecce essssaarryy ffo orr ffu uttu urre e sse errvviicciin ngg..
➢ ➢ IInnssppeecctt tthhiiss pprro od du ucctt tto o aassssu urre e yyo ou u h haavve e aallll p paarrttss rre eq qu uiirre ed d ffo orr
p prro op pe err iin nssttaallllaattiio on n..
➢ ➢ U Usse e o on nllyy aa ssttrraap p w wrre en ncch h o orr p prro otte ecctte ed d//ssm mo oo otth h--jjaaw w w wrre en ncch h o on n
aan nyy ffiin niissh he ed d ssu urrffaacce e..
➢ ➢ R Ru un n 3 3//4 4"" ssu up pp pllyy lliin ne ess ffo orr m maax xiim mu um m w waatte err ffllo ow w..
➢ ➢ D Do o N NO OT T u usse e p pu uttttyy d du urriin ngg tth hiiss iin nssttaallllaattiio on n..
➢ ➢ R Re effe err tto o tth he e ssp pe ecciiffiiccaattiio on n aan nd d aasssse em mb bllyy d drraaw wiin nggss aattttaacch he ed d..
FFaau ucce ett iiss sso olld d p paarrttiiaallllyy aasssse em mb blle ed d b bu utt ssh ho ow wn n ffu ullllyy d diissaasssse em mb blle ed d
ffo orr iillllu ussttrraattiivve e aan nd d sse errvviicce e p pu urrp po osse ess o on nllyy..
SIDE VALVE INSTALLATION:
1. With the lock nut (15) and lower sealing gasket (14) installed
on the side valve (13), insert the side valve into the hole in
the mounting surface so at least 1" of threads are exposed
above the deck surface.
2. Place the upper sealing gasket (11) onto the side valve then
thread the base escutcheon (10) onto the side valve.
3. Thread the handle assembly (1-9) onto the side valve until it
stops. Hand tight is adequate; if this assembly is too tight, the
handle will bind.
4. Unthread the base escutcheon until it contacts the gland nut
(6), which will assure proper side valve height.
5. Tighten the lock nut up against the underside of the
mounting surface to secure the side valve.
6. Repeat these steps to install the second side valve.
SPOUT INSTALLATION:
7. Unthread the diverter tee (32), locking nut (30) and lower
washer (29) from the spout (19).
8. Insert the spout assembly (17-28) through the hole in the
mounting surface with the upper washer (20) positioned
under the spout.
9. Reinstall the lower washer and tighten the locking nut to
secure the spout to the mounting surface.
10. Reattach the tee to the spout and fully tighten to prevent
leaks.
HAND SHOWER INSTALLATION:
11. Unscrew the locking nut (37) from the all-thread (42) and
remove the lower washer (38).
12. Unscrew the cover ring (44) from the all-thread and pull out
the plastic guide (43).
13. Insert the all-thread through the mounting surface, leaving
the escutcheon (41) and upper washer (40) in place.
14. Re-attach the lower washer and locking nut to the all-thread.
Fully tighten the locking nut to secure the assembly.
15. Slide the cover ring (44) over the conical end of the hose (36)
and insert the hose into the plastic guide (43). Now pass the
knurled end of the hose (36) through the all thread (42) until
the plastic guide is fully seated inside of the all-thread. Finally, re-
attach the cover ring to the all-thread.
16. Connect the conical end of the hose to the hand shower.
Note:The combination flow restrictor/non-return valve (45)
is located in the end of the hand shower.Final Connections
and Inspection