Waterworks Etoile Gooseneck Concealed Tub Filler Without Handshower and Metal Cross Handles - Manual

Flow restrictor / Backflow
protecton device
Note:
If the 24" flexible
supply hoses are
not long enough
to accommodate
the spread, NPT
adaptors
(GUMS 99) are
available
for running pipe.
Consult your local
building codes
for anti-scald
requirements
Inlets 3 ⁄ 4 " straight
male thread for
hose connection
8 1 ⁄
2
"
2 3 ⁄ 8 " 2 3 ⁄ 8 "
Etoile Concealed Tub Filler with Handshower & Diver ter
Installation Guidelines
ETHS 29
INSTALLATION GUIDELINES
➢
Use only a protected, smooth-jawed, or strap wrench on any finished surface.
➢ For proper installation, the deck surface should be installed prior to
mounting the mixer.
➢
It is recommended that an access panel be provided for future service.
➢
Check the specifications (left) for drilling sizes and suggested centers.
➢
Run 3 ⁄ 4 " supply lines for maximum water flow.
➢
Accessible shut-off valves, which will facilitate servicing, are recommended
for the hot and cold feed lines.
➢
To remove the trim from the valve body, unscrew the index to expose a
screw for the handle.The cover and escutcheon should be hand tight.
➢
DO NOT use putty on the deck fittings. Upper and lower washers are provided.
➢
When you screw the escutcheon onto the deck valve body, expose
several threads above it. Next, screw the valve cover down until it seats.
Then move the escutcheon up until it loosely meets the bottom of the
cover. Finally, tighten the bottom lock nut to secure the valve to the deck.
➢
Once the spout is securely mounted, install the flexible hoses between the
spout and valve bodies using the gaskets provided.
➢
If the handshower and diverter are used, do not use the “T” at the
bottom of the spout. Connect the hot and cold valves to diverter with the
hoses provided. A third hose is provided to connect the diverter to the
spout.The handshower hose is connected to the bottom of the diverter as
shown in the diagram (left).
➢
If the handshower and diverter are used:The diverter knob and escutcheon
unscrew to facilitate mounting the diverter to the deck.
➢
Note for handshower:The cone-shaped connector for the handshower
may be lodged in the hose escutcheon.To remove:Thread the handshower
down into the hose, pull up, remove the hose end, insert the washer, and
reconnect the handshower.
➢
After installation, unscrew and remove the aerator assembly. Carefully open
the hot and cold valves fully to flush out any debris in the supply lines.
Once the lines have been flushed, close the valves and reinstall the aerator assembly.
➢ IMPORTANT:
It is necessary to check for leaks and proper function of
mixer prior to being enclosed.
➢
If further assistance is required, please contact Product Support at
1-800-927-2120 (8am–7pm EST).
10" - 12"
11"
9"
Inlets 3 ⁄ 4 " straight
male thread
NPT adapters provided
Additional 24" flexible
hose provided with
ETHS 29 for connection to
spout (must remove “T”)
2 3 ⁄ 8 "
4"
2 7 ⁄ 8 "
Note:
Drilling hole sizes:
Sidevalves: 1
1 ⁄ 2 "
Spout, handshower,
and diverter: 1
1 ⁄ 4 "
Must have access
panel for servicing
ETTU 43
5/03
These guidelines have been prepared for the professional contractor to aid in the installation of:
ETOILE CONCEALED TUB FILLER (ETTU 43)
Handshower and diverter (ETHS 29) ordered separately.
All dimensions are based on original specifications and are subject to change and variation.
Please consult your Design Associate for current specifications.