HMDX Geo™ Alarm Clock EN - Manual (Page 2)

LIMITED 90 DAY WARRANTY
HMDX sells its products with the intent that they are free of defects in manufacture and workmanship for a period of 90 days from the
date of original purchase, except as noted below. HMDX warrants that its products will be free of defects in material and workmanship
under normal use and service. This warranty extends only to consumers and does not extend to Retailers.
To obtain warranty service on your HMDX product, contact a Consumer Relations Representative by telephone at 1-800-753-3000 or
email [email protected] for assistance. Please make sure to have the model number of the product available. Representatives
are available 8:30am-7:00pm EST Monday-Friday.
No COD’s will be accepted.
HMDX does not authorize anyone, including, but not limited to, Retailers, the subsequent consumer purchaser of the product from a
Retailer or remote purchasers, to obligate HMDX in any way beyond the terms set forth herein. This warranty does not cover damage
caused by misuse or abuse; accident; the attachment of any unauthorized accessory; alteration to the product; improper installation;
unauthorized repairs or modifications; improper use of electrical/power supply; loss of power; dropped product; malfunction or
damage of an operating part from failure to provide manufacturer’s recommended maintenance; transportation damage; theft; neglect;
vandalism; or environmental conditions; loss of use during the period the product is at a repair facility or otherwise awaiting parts or
repair; or any other conditions whatsoever that are beyond the control of HMDX.
This warranty is effective only if the product is purchased and operated in the country in which the product is purchased. A product that
requires modifications or adoption to enable it to operate in any other country than the country for which it was designed, manufactured,
approved and/or authorized, or repair of products damaged by these modifications is not covered under this warranty.
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. THERE SHALL BE NO OTHER
WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS OR ANY OTHER
OBLIGATION ON THE PART OF THE COMPANY WITH RESPECT TO PRODUCTS COVERED BY THIS WARRANTY. HMDX SHALL
HAVE NO LIABILITY FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. IN NO EVENT SHALL THIS WARRANTY
REQUIRE MORE THAN THE REPAIR OR REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO BE DEFECTIVE WITHIN
THE EFFECTIVE PERIOD OF THE WARRANTY.
NO REFUNDS WILL BE GIVEN. IF REPLACEMENT PARTS FOR DEFECTIVE MATERIALS ARE NOT AVAILABLE, HMDX RESERVES
THE RIGHT TO MAKE PRODUCT SUBSTITUTIONS IN LIEU OF REPAIR OR REPLACEMENT.
This warranty does not extend to the purchase of opened, used, repaired, repackaged and/or resealed products, including but
not limited to sale of such products on Internet auction sites and/or sales of such products by surplus or bulk resellers. Any and all
warranties or guarantees shall immediately cease and terminate as to any products or
parts thereof which are repaired, replaced, altered, or modified, without the prior express and written consent of HMDX. This warranty
provides you with specific legal rights. You may have additional rights which may vary from state to state. Because of individual
regulations, some of the above limitations and exclusions may not apply to you. For more information regarding our product line in the
USA, please visit: www.hmdxaudio.com
For more information regarding our product line in the USA, please visit: www.hmdxaudio.com
Por manual de instrucciones e información de garantía en español visítenos en www.hmdxaudio.com
HMDX is a trademark of HMDX. ©2013 HMDX. All Rights Reserved.
PRE-SET CLOCK
This unit is equipped with a pre-set clock, meaning
the clock will automatically set itself when first plugged
in. Please note: the clock will automatically default to
Eastern Standard Time and will need
to be adjusted for other time zones by manually
setting the clock.
SETTING CLOCK TIME
1. Press (2 seconds) and release TIME SET button on back of unit,
select the hour using the +/- buttons on the top to adjust the
hour, press TIME SET button again to select the minute using
the volume buttons on the top again to adjust the minutes. Press
TIME SET button again and time is now set.
2. Select 12/24 hour display read out by pressing the 12/24 button
on the back of the unit.
NOTE: PM will be indicated when in 12 hour mode only.
SETTING THE ALARM
1. Press and hold the ALM button on back of unit for 3 seconds. The
hour will begin flashing.
2. Use the +/- buttons on top of the unit to adjust the hour, paying
attention to the AM and PM indicators (when in 12 hour mode).
3. Press and release the ALM button again and the minute will
begin flashing. Use the +/- buttons on top of the unit to adjust the
minutes.
4. Press the ALM button again and the alarm is now set and will
appear in the display.
SNOOZE OPERATION/TURNING OFF THE ALARM
Press the SNOOZE bar located on the top of the unit when the alarm is
activated, the alarm will sound again in nine minutes.
To turn off the alarm, press the ALM button on the back of the unit, the
will no longer appear.
Press the ALM button at any time to reactivate the alarm mode, the
symbol will appear on display.
NOTE: The alarm time will default to last time set.
DISPLAY DIMMER CONTROL
Press the SNOOZE/DIMMER bar to adjust the intensity of the clock
display.
BACKUP BATTERY
This alarm clock is equipped with a battery backup feature (1 CR-2032
battery included and already installed) to keep the clock time and alarm
settings during power outage. The battery is located
on the bottom of the unit for easy access.
MAINTENANCE
To Store:
You may leave the unit on display, or you can
store it in a cool, dry place.
To Clean:
Only use a soft dry cloth to clean the enclosure of the unit.
NEVER use liquids or abrasive cleaners to clean.
FCC DISCLAIMER:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: The
manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit • Consult the dealer or an experienced radio/TV technician for help.
different from that to which the receiver is connected.
IB-HXB070