Rane MP 24z - Manual (Page 6)

Manual-4
REAR PANEL DESCRIPTION
1 BALANCED MAIN OUTPUT connectors: Provide a fully balanced Main Output signal—pin 2 is (+), pin 3 is (–) and pin 1 is
signal ground. Pin 3 must never be grounded for unbalanced operation. Use only pin 2 as hot and pin 1 as return for any unbalanced
operation.
2 UNBALANCED MAIN OUTPUT connectors: Provide Main Output signals on ¼" TS (tip-sleeve) unbalanced connections.
3 BOOTH OUTPUT connectors: The Left Output only supplies a mono Booth Monitor Output; connecting to both Left and
Right provides a stereo Output.
4 ZONE OUTPUT connectors: The Left Output only supplies a mono Zone Output, connecting to both Left and Right provides
a stereo Output. The Zone Outputs are located Post-EQ, which includes the Microphone Output. An internal jumper block pro-
grams the Zone to Pre-EQ (and no mic) if required. (See Service Information on page Manual-9.)
5 MAXIMUM OUTPUT GAIN REDUCTION control: Decreases the maximum Level of the balanced and unbalanced MAIN
OUTPUTS of the MP 24z as it is rotated counter-clockwise.
6 METER SENSITIVITY ADJUST: Clockwise rotation decreases the full-scale sensitivity of the PEAK PROGRAM METER, as
indicated by the full-scale voltage calibrations around the control.
7 SYSTEM MONO/STEREO switch: Engaging this pushbutton converts all Outputs (except tapes and loops) to MONO, regard-
less of the nature of the Input signals.
8 EQ RANGE switch: In the out position, the maximum boost/cut available from the Program Equalizer is ±8 dB. In the switch’s
in position, this range is reduced to ±4 dB.
9 LIGHT CONTROL OUTPUT jack: Provides a transformer-coupled mono program signal for use by a lighting controller’s trig-
ger input. This is a balanced ¼" output—the tip is positive, the ring is negative and the sleeve is floating.
0 LIGHT OUTPUT LEVEL attenuator: Counter-clockwise rotation reduces the Output Level at the LIGHT CONTROL OUT-
PUT jack.
METER SENSITIVITY ADJUST
OFF
5V
TO ALL OUTPUTS. INSTALL IN
UNUSED INPUTS ONLY.
CHASSIS
CLASS 2 EQUIPMENT
GND
SIG GND
LIFT
10V
6V
GAIN REDUCTION
MAX OUTPUT
-22 0
dB
-6
UNBALANCED
POST LOOP
"STORE" PHONO SHORTING PLUGS
IN TAPE OUT JACKS. THIS WILL
SHORT SIGNAL PATH TO GROUND
CAUSING A LOW DISTORTED SIGNAL
DO NOT UNDER ANY CIRCUMSTANCE
UNBALANCED
MONO *
L R
±4dB
PRE LOOP
R
±8dB
L
UNBALANCED
*
PLUGGING ONLY INTO
LEFT YIELDS L+R
OUTPUT. PLUGGING
INTO BOTH YIELDS
MONO OUTPUTS
STEREO OUTPUT.
RETURN RETURN
L R
MONO*
BALANCED
FULLY
SEND
MONO*
SEND
L R
RETURN SEND
L L
WIRELESS
USE FOR
MICS
1.7V
1V
0.6V
2.5V
3.5V 4V
SYSTEMS
LIGHT OUTPUT LEVEL
0 10
2
4
8
6
+15V
DUCKER
BOOTH ACTIVE
DEFEAT
RING=RETURN
TIP=SEND
PHANTOM
POWER
GROUNDING POST
CASE: CHASSIS
3: NEGATIVE
1: COMMON
2: POSITIVE
USING INTERNAL RIAA DEFEAT JUMPERS
RANE CORP.
MADE IN U.S.A.
N108
BALANCED
UNBALANCED
AND PIN 1 FOR
USE ONLY PIN 2
PIN 3 TO GND!
DO NOT SHORT
CASE: CHASSIS
3: NEGATIVE
2: POSITIVE
1: COMMON
OUTPUT
RETURN SEND
R R
LINE 6
R
LINE 5
L
LIGHT CONTROL OUTPUT
TRANSFORMER COUPLED
MONO
LINE 4
R
AUX 3
L
PH 2
R
LINE 3
L
R
L
PH 3 AUX 2
MIC
LINE 2
L R
LINE 1 PH 1
AUX 1 SWITCHABLE LOOP TAPE OUT EQ
RANGE
ZONE OUTPUT
MONO
MAIN OUTPUTS
OUTPUT
BOOTH
MAIN EFFECTS LOOP SYSTEM
(HI-Z ONLY)
LOOP
MIC
AUX
MIC
MAIN
MIC
R
L
R
CAUTION
L
R
L MP 24z
POWER
750mA
8
28 26 27 5 3 6 10 20
11 7 4 15 14 13 12
24
23
21
1 2 9 25 18 19 17 16