Beckett 61828 12V Oil Igniter - Manual

INSTALLATION INSTRUCTIONS
ELECTRONIC OIL IGNITER ● 12 VDC
Electrical Shock Hazard
Electrical shock can cause severe personal
injury or death.
Disconnect all electrical power to the burner before servicing.
More than one disconnect switch may be in the supply circuit.
Installation and service must only be performed by a qualifi ed
service technician.
Remove all jewelry, such as rings and watches before servicing.
Provide ground wiring to the burner, metal control enclosures
and accessories. (This may also be required to aid proper control
system operation). y
y
y
y
APPLICATION INFORMATION:
This igniter is designed for use with 12 VDC.
It is rated for continuous duty and can be used with
intermittent, or interrupted ignition primary controls.
The Beckett oil igniter is designed to mount in the same
manner as standard ignition transformers and igniters.
This igniter can be adapted to multiple base plates to
accommodate Beckett ADC & SDC burners. It will also fi t
on many other vendors’ transformer base plates.
CAUTION! Do not use this igniter beyond its design
specifi cations. Improper operation and igniter failure may
result.
◦
◦
◦
◦
SPECIFICATIONS:
Input Voltage: 10.8 - 16 Vdc
Output Voltage: 20 kV peak
Output Current: 25 mA RMS
Input Current: 1.8A
Ambient Operating Temperature: -40 to +150° F
Storage Temperature: -40 to +150° F
Moisture: 5 to 95% Relative Humidity, Condensing
Table 1 - Complete Igniter Base Plate Assemblies
Part No. Burner Models
5218301U Beckett ADC 12 Vdc
5218303U Beckett SDC 12 Vdc
5218307U Wayne ‘M’ Models for 12 Vdc
5218305U Wayne ‘E’ Models for 12 Vdc
5218309U Igniter Only
Note: Use #6 x 7/16” screws when using the bottom mounting
holes. Use #10 thread forming paint scraping screws, if using
the two top mounting holes for 5218301 & 5218302.
Tighten all screws securely.
Install the barrier and base plate gaskets for Beckett Model
ADC only.
Use gaskets for other burner models, as required by the
manufacturer.
Use of top mounting screws is possible for Beckett Models
ADC and SDC.
Mount the assembled unit to the burner using the screws
supplied.
Use “paint scraping” screws for all burners (2 at the hinge and
2 for non-hinged base plates). Tighten these screws securely
to provide effective grounding to burner housing.
Verify the burner is properly grounded.
Install the cad cell if applicable. Carefully route the igniter
input and cad cell leads to prevent them from being pinched
during closing.
Constant Duty Ignition - Without Primary Control
Carefully follow the equipment manufacturer’s wiring
instructions and diagrams. Connect the Black lead to 12
Vdc circuit Ground (-).
Connect the Blue-White and solid White leads together and
wire to 12 Vdc circuit (+), parallel with burner motor.
The Yellow leads from the igniter will not be used and shall
be wire nutted individually and placed in the housing wiring
compartment.
Interrupted Ignition - Without Primary Control
Carefully follow the equipment manufacturer’s wiring
instructions and diagrams.
Connect the Black lead to 12 Vdc (-) circuit Ground.
Connect the solid White lead to the 12 Vdc (+) circuit,
downstream of limit/operating controls and parallel with the
burner solenoid valve.
Connect the Blue-White lead to 12 Vdc (+) circuit , parallel
with burner motor.
Connect the Yellow leads from the igniter to the Yellow Cad
Cell leads with the wire nuts.
Wiring Igniter to GeniSys 12 Vdc Primary Control
Carefully follow the control, or equipment manufacturer’s
wiring instructions and diagrams.
Fasten cad cell leads to control CAD CELL spade
terminals.
Attach the Black lead with insulated fl ag terminal to the
primary control GND (IGN) spade terminal.
Combine the Blue-White striped and solid White leads
and jumpers, and attach its insulated fl ag terminal to the
primary control IGNITER spade terminal.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
▪
▪
▪
14.
▪
▪
▪
▪
▪
15.
▪
▪
▪
▪
Installation Instructions:
(If base plate is already installed, skip to step number 9)
Locate the igniter input leads.
Install the 32743 igniter gasket, if required, and route the
leads through the appropriate base plate lead exit hole. Make
sure these leads are not being crushed.
Mount the igniter fl ush to base plate with the mounting screws
supplied. 1.
2.
3.