Panasonic PV-C911 - Manual (Page 42)

efore Requesting bervice
Check the following points once again if you are having trouble with your unit.
Power Correction
No power... • Completely insert Power Plug into an AC outlet or when using
the DC Car battery cord, check to see it the fuse is blown.
• Set POWER button to ON.
Monitor Correction
No picture or Sound-
Poor picture with normal sound...
Poor sound with normal picture...
Poor TV reception...
No color or poor color...
Ghost (multiple) images...
TV programs cannot be watched...
Channel cannot be selected...
• Make sure your antenna system (TV or CABLE), is correctly set. (P. 8-11)
• Completely insert Power Plug into an AC outlet. (Or use the DC Car
Batteiy cord.)
• Set POWER button to ON.
• Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the
SET UPTV menu. (P.17)
• Adjust VOLUME control. (P. 16)
• Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P. 17)
• Adjust TINT and COLOR controls in the SET UP TV menu. (P. 17)
• Install a directional antenna.
• Make sure the selected channel is in unit’s memory. (P. 12,13)
• Only the channel being recorded can be viewed on this unit.
VCR Correction
TV program cannot be recorded...
Timer recording cannot be
performed...
No playback picture, cwthe playback
picture is noisy or contains streaks...
VCR cannot be controlled...
• Make sure your antenna system (TV or CABLE), is correctiy set. (P. 8-11)
• Make sure cassette record tab is intact. (P.4)
• Check that dock is set to current time and date.
• Make sure DSS/CABLE box (if used) is left on and tuned to channel to
be recorded.
• Set recording Start/Stop times correctty. (P. 24-25)
• Timer recording may not be performed or continued if a power
interruption of more than 1 minute occurs before or during a Timer
recording even after power is restored.
• Adjust TRACKING control in either direction. (P. 41)
• Try Head Cleaning, (P. 41)
• Make sure VCR LOCK is set to off. (P. 32)
• Make sure unit is not in a Timer Record operation.
Remote Control Correction
Unit cannot be controlled...
ACTION, PROG and FM/TV
buttons cannot be selected...
• Aim remote at remote sensor on unit (P. 7) so that signal is
unobstructed.
• Inspect the remote batteries. (P. 4)
• Make sure VCR LOCK is set to off. (P. 32)
• Exposing unit remote sensor to direct fluorescent or outdoor light may
cause signal interference.
• Check remote batteries.
Miscellaneous Correction
Video cassette cannot be
inserted...
Video cassette cannot be
removed...
Tape cannot be'ejected or
inserted...
Video cassette ejects when a
recording is started, or the power
is turned off for timer recording...
In Stc^ mode, the VCR motor
(CYLINDER) continues to rotate...
VCR cannot be controlled...
• Insert the cassette window side up; record tab facing you.
• Completely insert Power Plug into an AC outlet. (Or use the DC Car
Battery cord.)
• Try ejecting or inserting the tape again after turning POWER off, then
back on.,
• Make sure cassette record tab is intact. (P. 4)
• To enable Quick Play mechanism, the VCR cylinder will rotate for
about 3 minutes. This reduces response time from Stop to Play mode
and from Play to Rewind Search mode.
• Make sure VCR LOCK is set to off. (P. 32)
If you cannot resolve the problem, please call the Customer Satisfaction Center for
product assistance at 201-348-9090.
To locate an authorized servicenter call toll free 1-800-211-PANA(7262)
or send e-mail to : [email protected].
42
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to ; [email protected]