Panasonic RX-CS710 - Manual (Page 6)

RADIO TAPE PLAYBACK
1. Set the Function Selector to “RADIO"’.
2. Set the Band Selector to the desired radio band.
3. Tune in your favourite station using the Tuning Control.
4. Adjust the Volume and Graphic Equalizer Controls to
the desired settings.
(Refer to "Graphic Equalizer’’.)
5. The radio can be turned off by setting the Function
Selector to “TAPE/[o^’’.
Notes:
•To receive FM stereo broadcasts, set the FM Mode
Selector to “STEREO ”.
The FM Stereo Indicator will light during stereo
broadcasts.
• If FM stereo reception is poor (excessive noise, FM
Stereo Indicator flickers), set the FM Mode Selector
to “MONO”.
This will reduce the noise and provide clear
reception; however, the broadcast will not be heard
in stereo.
■ Graphic Equalizer
it allows you to tailor the frequency response of the unit to
compensate for room acoustics and other factors which
affect frequency response. The overall tone can be altered
by adjusting the five controls which control the following
frequency bands:
100 Hz, 330 Hz, 1 kHz, 3.3 kHz, 10 kHz.
Positioning the control to the “+" side of the detent will
amplify the corresponding frequency band; the side
will attenuate it.
■ Antennas
FM;
Pull out the Telescopic Antenna and adjust its length and
angle for optimum reception.
AM:
The sensitive ferrite core antenna inside the set will provide
excellent AM reception in most areas. For optimum recep­
tion, turn the set in the direction which gives the best results,
since the ferrite core antenna is directional.
1. Open the Cassette Compartment cover by pressing the
Stop/Eject Button. Insert the cassette as shown in the
figure, and then close the Cassette Compartment cover.
Note:
Make sure the exposed part of the cassette tape
faces down. If it Is upside down, the Cassette
Compartment cannot be closed. Do not try to force it
shut.
2. Set the Function Selector to “TAPE/joF^".
3. Press the Playback Button to begin tape playback.
4. Adjust the Volume and Graphic Equalizer Controls to
the desired settings.
5. To stop playback, press the Stop/Eject Button.
Otherwise, at the end of the tape, the Playback Button
will be refeased and the unit will be shut off automatically.
■ Full Auto-Stop
During playback, recording, fast forward or rewind when the
tape reaches its end, the automatic stop system will release
the operation buttons and automatically turn the unit off.
Note that the unit is not turned off if the Function Selector is
set to “RADIO" or "rcDl/LINE”. it must be set to “TAPE/
■ Fast Forward and Rewind
The tape will move rapidly forward when the Fast Forward/
Cue Button is pressed.
The tape will be rewound rapidly when the Rewind/Review
Button is pressed.
Note:
Do not press the Playback Button during fast forward
or rewind, as this may jam the tape. Always press the
Stop/Eject Button first, between functions.
■ Cue and Review
If the Fast Forward/Cue Button (or Rewind/Review Button)
is pressed during playback, the recorded sound on the tape
can be monitored at a fast speed.
When the button is released, playback will resume.
■ Pause Button
The Pause Button can be used to temporarily stop the tape
from moving during recording or playback.
Before beginning a recording, first press and lock the Pause
Button. Then, press the Record Button. (The tape will not
move.) When ready to record, press the Pause Button to
release it. This will start tape movement for immediate
recording.
Note:
Do not use the Pause Button to stop the tape for a
long period of time.
The unit is not turned off when the Pause Button is
pressed. Always use the Stop/Eject Button to turn the
unit off.