Clarion DXZ938R - Manual (Page 27)

DXZ938R
31
English
Digital Radio / DAB Operations
Switching programmes
1. Press the [FNC] button to receive a DAB station.
2. Press the [ a ] or [ d ] button to switch
programmes in the DAB station.
Note:
• The programme name may be the same depend-
ing on DAB programmes.
Programme scan
This function scans through each receivable
programme in a DAB station being received for
10 seconds sequentially. This is useful when you
want to search for a desired programme.
1. Press the [FNC] button to receive a DAB station.
2. Perform the following operation depending
on the connected model.
Press the [P/A] button. “SERVICE SCN”
lights up and the unit starts scanning each
programme for 10 seconds sequentially.
Each time the main unit scans, the
programme name is shown in the display.
3. To stop programme scan when a desired
programme is tuned in.
Press the [P/A] button.
Manual memory
The main unit has a manual memory function for
DAB programmes. Up to 18 programmes (6
programmes each) can be preset in the preset
buttons.
[M1], [M2] and [M3]
1. Press the [FNC] button to select the DAB
mode.
2. Press the [BND] button to select any one
shown above.
3. Press the [ a ] or [ d ] button to select a de-
sired programme.
4. Press and hold one of the [DIRECT] buttons
(1 to 6) for 2 seconds or longer to store the
programme.
Note:
• The interrupt programme (PTY or INFO) cannot
be written into a manual memory.
Recalling a preset programme
1. Press the [FNC] button to select the DAB mode.
2. Press the [BND] button. Each time you press
the [BND] button, the display changes in the
following order:
[M1] ➜ [M2] ➜ [M3] ➜ [M1]...
3. Press one of the [DIRECT] buttons to recall a
preset programme.
Note:
• Press and hold the [DIRECT] button for 2 sec-
onds or longer to store the programme currently
being received. (Manual memory)
AF function
The AF function switches to a different fre-
quency on the same network in order to main-
tain optimum reception.
∗
The factory default setting is “ON”
∗
If the reception of the current broadcast station de-
teriorates, “SEARCH” appears in the display and
the radio searches for the same programme on
another frequency.
∗
For details on “AF function”, refer to the section
“RDS operation” of each owner’s manual.
● Switching OFF the AF function
● Switching ON the AF function
● AF function between RDS and DAB
When the same programme is broadcast by
both RDS and DAB, and this function is ON, the
main unit switches to receiving the broadcast
with the better reception automatically.
TA (Traffic Announcement)
In the TA standby mode, when a traffic announce-
ment broadcast starts, the traffic announcement
broadcast is received as top priority regardless of
the function mode. Traffic programme (TP) auto-
matic tuning is also possible.
∗
This function can only be used when “TP” is lit in
the display. When “TP” is lit, this means that the
DAB or RDS broadcast station being received has
traffic announcement programmes.
∗
For details on “TA”, refer to the section “RDS op-
eration” of each owner’s manual.
● Setting the TA standby mode
● Cancelling the TA standby mode
● Searching for a TP station
Notes:
• If a TP station is not received, the main unit stops
the search operation.
• “TP” may be lit in the display when a TP broad-
cast is transmitted from an RDS station. In this
case, press the [TA] button to perform TP seek
tuning. Press the [TA] button again to return to the
previous mode.