Cambridge Audio AZUR 650R - Manual (Page 8)

8
Remote control
Mute
Mutes the audio on the AV Receiver. Press again to cancel
mute.
Volume
Increase or decrease the volume of the AV receiver output.
Also used as up/down in the OSD setup menus.
Tune / Left & Right
Press the right arrow to increase tuner frequency/change
preset. Press the left arrow to decrease tuner
frequency/change preset. Also used to scroll left/right in the
OSD setup menus.
Enter
Used in the OSD setup menus.
On-Screen Display (OSD)
Press to turn on and off the on-screen setup menus for display
on your monitor/screen.
Bass/Treble
Press for bass/treble adjustment, using the Volume up/down
buttons. Note: Bass/Treble is bypassed in analogue stereo
direct and 7.1 direct modes.
7.1 Direct
Selects the 5.1/6.1/7.1 direct input.
Audio In Type
Switches the audio between the types available for the current
source. Depending on the source selected and whether you
have assigned an HDMI input to it, Analogue, Digital and HDMI
can be available.
Video In Type
Switches the video between the types available for the current
source. Depending on the source selected and whether you
have assigned an HDMI input to it, Composite, S-Video,
Component and HDMI types can be available.
Note: The 650R cannot simultaneously receive HDMI audio
and analogue video from the same source.
For any HDMI audio sources selecting analogue video will then
cause the unit to switch to analogue audio as well. Digital
audio via SPDIF/Toslink can then also be selected via the
Audio Input Type button but not HDMI audio. Returning to
HDMI video will allow selection of HDMI audio (or indeed
analogue or digital audio) again.
Lip sync
Press to activate and adjust the lip sync delay function if the
audio and video appear out of sync. While the Lip sync delay
status is shown on the units display, use the Vol
and Vol
buttons to adjust the delay time. Adjusting the value to zero
causes lip sync delay to be turned off. See later section in this
manual.
Tuner AM/FM, BD/DVD, Video 1, Video 2, Rec
1, Aux, CD, Rec 2
Press the corresponding button to change the input source.
Pressing the Tuner AM/FM button a second time toggles
between AM and FM modes.
The above button descriptions are naturally brief. Please
refer to the ‘Operating Instructions’ section of this manual for
more information on the relevant functions implemented.
The 650R is supplied with an Azur Navigator remote control.
Insert the supplied AAA batteries to use. For full details of the
various adjustment functions available from the remote, refer
to the later sections of this manual.
Standby/On
Switches the unit between Standby mode and On.
Analogue Direct
Directly selects a stereo analogue input for the current source
with no A/D conversion or DSP processing.
Stereo Modes
Selects Stereo or Stereo + Sub modes for Analogue or Digital
sources (digitally processed).
PLIIx/Neo/DSP
Selects from various matrix encoded surround processing
modes for analogue or digital sources (digitally processed).
DD/DTS Modes
Selects digital surround processing modes for Digital/HDMI
sources only.
Dynamic
Press repeatedly to reach the desired dynamic compression
range (Dolby Digital or DTS modes only).
Sub On/Off
The Sub On/Off button performs temporary muting of the
Subwoofer without affecting the bass management or
speaker settings. Pressing the Sub On/Off button again or
selecting another decode mode cancels Sub Mute.
To make permanent settings to the speaker options including
the Subwoofer, use the ‘Speaker Config Menu’ in the On
Screen Display (OSD).
Also, hold down and then press the volume up and down
buttons to adjust the overall sub level if desired.
PTY (Program Type Search)
Press to search by program type when in Tuner mode. Refer
to the ‘Operating instructions’ section of this manual for more
information.
APS (Auto Program Search)
Hold down for 4 seconds to allocate and memorise radio
stations automatically.
Display
Press to view the current source material and decoding mode.
Press again whilst the current decoding mode is scrolling (as
long as mute is not on) to display the incoming sample rate.
When listening to FM with RDS, press to cycle round various
RDS information modes.
Stereo Mono
When listening to FM, press to alternate between stereo and
mono modes.
Store
Press to store the current frequency when in Tuner mode.
Mode
Press to select Auto/Manual or Preset tuning when in Tuner
mode.
Enter
Vol
Vol
Analog
Direct
7.1
Direct
DD
DTS
Dynamic
Stereo
Modes PL IIx
Neo/DSP
Sub
On/Off
Store Mode
Video 1
BD
DVD
Tuner
AM/FM
Video In
Type
Lip
Sync
Audio In
Type
Bass
Treble
Video 2 Rec 1 Aux
CD Rec 2
Stereo
Mono
Display PTY APS