Conair CID110 - Manual (Page 3)

TO INSTALL BATTERIES
Batteries are required for the Caller ID functions and Telephone
operations of the unit.
1. Open the battery door by pulling back the latch.
2. Insert three (3) AA alkaline batteries (not included).
3. Snap the battery door back into place.
Note: Once batteries are installed, you have 20 seconds to setup
the Caller ID.
SETTING UP YOUR CID110
DO NOT CONNECT the line cord to the wall outlet until the
Caller ID setup has been completed.
NOTES:
• If the Caller ID is not setup within 20 seconds after battery
installation, press and hold both the [ ] and [ ] keys for 4
seconds to activate the Caller ID setup.
• If you do not have the Caller ID service and want the time/
date set, please go to Caller ID setup section and ‘ENTER
TIME DATE’ setting.
The LCD shows ‘ENTER LANGUAGE’
followed by a choice of 3 languages
(English, Spanish, French).
The LCD then shows ‘ENG ESP FRA’.
NOTE: The ‘ENG’ is BLINKING. Press
[ ] or [ ] to select ‘ENG’, ‘ESP’, or ‘FRA’.
Press [ERASE] to confirm.
If ENG is selected, the LCD shows ‘LCD
CONTRAST’.
Press [ ] or [ ] to adjust five levels (from
1 to 5, default is 3) contrast of LCD.
Press [ERASE] to confirm.
If contrast is set, the LCD shows
‘ENTER AREA CODE’. The first digit
‘–’ of the area code will blink.
Press [ ] or [ ] to enter the area code.
Press [ERASE] to confirm and go to next entry.
Repeat above steps until 3-digit area code is set.
4 5 6
If area code is set, the LCD shows
‘ENTER TIME DATE’.
Press [ ] or [ ] to select the hour digits.
Press [ERASE] to confirm and go to the next entry.
Press [ ] or [ ] to select the minute
digits.
Press [ERASE] to confirm and go to the
next entry.
Press [ ] or [ ] to select the month digits.
Press [ERASE] to confirm and go to the
next entry.
Press [ ] or [ ] to select the date digits.
Press [ERASE] to confirm.
The LCD shows ‘TOTAL:00 NEW:00’,
which means both the total call and new
call counter are zero.
USING THE PHONE ON A DESK
1. Plug the long telephone line cord into the jack in the bottom
of the BASE, thread it through the groove toward the back of
the unit, then plug it into the modular phone jack.
2. Connect the COIL CORD to the jack in the HANDSET and
the BASE.
HANGING THE PHONE ON THE WALL
When the CID110 is wall mounted, the HANDSET GUIDE holds
the handset in place in the cradle.
On a wall phone plate
1. Plug the short telephone line cord into the jack in the base
bottom and into the jack on the plate.
2. Hang the base on to the two pins and pull the base down to
lock it on.
3. Plug the coil cord into the handset and base jacks.
On a wall without a plate
1. Install 2 screws with anchors into the wall, one above the
other, 3-1/4" apart, extending 3/16" out from the wall to hold
the base securely.
2. Install the long telephone line cord into the jack in the base,
thread it through the groove and plug it into modular wall
jack.
3. Hang the base on the screws and pull it down to lock it on.
4. Plug the coil cord into the handset and base jacks.
TELEPHONE FEATURES
Tone/Pulse Switch
Set switch to your type of service. If you don’t know whether you
have tone or pulse:
1. Put the switch on “Tone”.
2. When you have a dial tone, press any key on the keypad. If
the dial tone stops, leave it on “Tone”. If not, change the setting
to “Pulse”.
Receiver Volume Control
The receiver volume control is located on the side of the handset
of your phone. This enables you to adjust the receiver volume
from NORM to HI for a better listening level.
Ringer Off/Low/High
Your CID110 features a harmonic dual tone ringer that can be
adjusted from a loud (HI) to a soft (LO) sound level. When you
don’t want to be disturbed, slide the switch to the OFF position.
You can still make outgoing calls without being disturbed by
incoming calls.
Pause
Whether you have Tone or Pulse service, you can insert a 4-
second PAUSE into the dialing or storing of a number into
memory in order to access custom and telebanking services,
long distance, etc. Press [Redial] at the desired point in the
number. Press [Redial] again if an additional 4 seconds is
needed.