Brookfield Lab Stand - Manual (Page 2)

Model A & Model A 18 Model G & Model G 18 Model QB
Model A Lab Stand - Comes with 14” rod
(VS-CRA-14S). Used with Dial and DV-E
viscometers.
Model A 18 Lab Stand - Comes with 18”
rod (VS-CRA-18S). Optional choice when
additional height is required.
UnpAckinG
Check to see that all the components are
received with no concealed damage:
1 VS-1 Base with three leveling screws
1 VS-CRA-14S (Model A) or
VS-CRA-18S (Model A 18) Rod and
clamp assembly with one mounting
screw and washer.
AsseMBly
1. Remove the mounting screw and
washer from the upright rod. Place
the rod and clamp assembly into the
hole in the top of the base.
2. Position the rod and clamp assembly
so that the clamp assembly has the
“FRONT” marking facing forward.
3. While holding the rod and base
together, insert the screw and washer
as shown and tighten securely.
4. Adjust the tension screw so that the
clamp assembly is not loose on the
upright rod.
ViscoMeter MoUntinG And Use
Insert the Viscometer mounting rod into
the hole (with the cut-away slot) in the
clamp assembly. Adjust the viscometer
level until the bubble level is centered and
tighten the clamp knob (clockwise). Use
the base leveling screws to “fine” adjust the
viscometer level.
cAUtion: Do not tighten the clamp
knob unless the viscometer mounting rod
is inserted in the clamp assembly.
Model QB Lab stand - Comes with 14”
rod (VSQA-100Y). Used with DV2T
Extra Viscometers and DV3T Extra
Rheometers. Also available as optional
choice for other viscometers when easier
up/down movement of viscometer head
is desired.
cAUtion: The Model QB upright rod
is a spring-loaded, non-serviceable device.
Do not disassemble the clamp and upright
rod assembly.
UnpAckinG
Check to see that all the components are
received with no concealed damage:
1 GV-1201 Base with two leveling screws
1 VSQA-100Y Clamp and upright rod
assembly with one mounting screw
and washer
AsseMBly
1. Remove the mounting screw and
washer from the upright rod. Place the
rod and clamp assembly into the hole
in the top of the base with the release
lever facing forward.
2. Position the rod and clamp assembly
until the slot on the bottom of the rod
intersects the pin located in the base.
3. While holding the rod and base
together, insert the screw and washer
as shown and tighten securely.
ViscoMeter MoUntinG And Use
Insert the viscometer mounting rod into
the cutaway slot of the clamp assembly.
Adjust the instrument until the viscometer/
rheometer bubble level is centered
and tighten the clamp knob. Use the
base leveling screws to "fine" adjust the
instrument level.
cAUtion: Do not tighten the clamp
knob unless the viscometer mounting rod
is inserted in the clamp assembly.
Push the release lever on the clamp
assembly. Move viscometer/rheometer
head to desired height and release lever.
Elevate your sample container, if necessary,
to ensure that the proper spindle
immersion is achieved.
cAUtion: Do not use the DV2T or
DV3T with any other laboratory stand that
does not utilize the GV-1201 base. This large
base is necessary for stability of the DV2T
Viscometer and DV3T Rheometer during
use. Earlier versions of the Brookfield
Laboratory Stand including Model A and
Model S should not be used with the DV2T
or DV3T.
Model G Lab Stand - Comes with 14” rod
(VS-CRA-14S). Used with DV1, DV2T
Viscometers and DV3T Rheometers.
Model G 18 Lab Stand - Comes with 18”
rod (VS-CRA-18S). Optional choice when
additional height is required.
UnpAckinG
Check to see that all the components are
received with no concealed damage:
1 GV-1201 Base with two leveling screws
1 VS-CRA-14S (Model G) or
VS-CRA-18S (Model G 18) Rod and
clamp assembly with one mounting
screw and washer.
AsseMBly
1. Remove the mounting screw and
washer from the upright rod. Place
the rod and clamp assembly into the
hole in the top of the base.
note: Be sure the clamp assembly has
the “FRONT” marking facing forward.
2. Position the rod and clamp assembly
until the slot on the bottom of the rod
intersects the pin located in the base.
3. While holding the rod and base
together, insert the screw and washer
as shown and tighten securely.
4. Adjust the tension screw so that the
clamp assembly is not loose on the
upright rod.
ViscoMeter MoUntinG And Use
Insert the Viscometer mounting rod into
the hole (with the cut-away slot) in the
clamp assembly. Adjust the viscometer
level until the bubble level is centered and
tighten the clamp knob (clockwise). Use
the base leveling screws to “fine” adjust the
viscometer level.
cAUtion: Do not tighten the clamp
knob unless the viscometer mounting rod
is inserted in the clamp assembly.
cAUtion: Do not use the DV2T or
DV3T with any other laboratory stand that
does not utilize the GV-1201 base. This
large base is necessary for stability of the
DV2T Viscometer and DV3T Rheometer
during use. Earlier versions of the
Brookfield Laboratory Stand including
Model A and Model S should not be used
with the DV2T or DV3T.
M13-125-B1014