Delptronics Ring Modulator - Manual

Email Questions or Comments to [email protected]
Assembly Instructions
Introduction:
4 Diodes:
3 Resistors:
2 Ceramic Capacitors:
1 Electrolytic Capacitor:
1 Chip:
1 Switch:
3 Jacks:
2 Transformers:
1 Battery Connector:
Hardware:
For ease of assembly, we recommend
that the shorter parts be inserted and soldered first, that
is the order that the parts are listed below. The printed
circuit board has an outline for every part, but not every
outline is labeled. For clarification, please refer to the
photograph of the finished kit.
If this is the first
electronic kit you have assembled, please read the
soldering tutorial first.
The four identical germanium diodes look
like little glass tubes with a green or black stripe on
them. Diodes are polarized, so the direction that they
are inserted into the circuit board is important. The
negative lead (wire) of the diode is on the side marked
with the stripe. The negative lead on the circuit board is
also marked with a stripe. The leads need to be bent
close to the body of the diode. Hold the diode body and
press down on each lead right at the body to make a U
shape.
There are two 1K resistors (marked with
brown, black, black, brown, brown stripes) and one 10K
resistor (marked with brown, black, black, red, brown
stripes). Resistors can be inserted in either direction.
The leads need to be bent close to the body of the
resistor. Hold the resistor body and press down on
each lead right at the body to make a U shape.
The ceramic capacitors look
like little blue blobs. They can be inserted in either
direction. The two ceramic capacitors look very similar,
so please check the marking on the capacitor.
is marked with the number 105 and the 0.47 µF
capacitor is marked with the number 474.
The 4.7 µF electrolytic
capacitor looks like a little black and gray tin can.
Electrolytic capacitors are polarized, so the direction
that it is inserted into the circuit board is important. The
negative lead on the capacitor is shorter and is marked
with a gray stripe on its body. The positive hole on the
circuit board is marked with a plus sign.
The 555 timer chip looks like a tiny black box
with eight short wire legs. Make sure that the notch on
the top of the chip lines up with the notch on the circuit
board outline.
The switch can only be inserted one way.
Make sure that it is seated flush against the circuit
board, especially if you intend to mount the Ring
Modulator in a panel or enclosure. You may want to
tape it down while you solder it.
The jacks snap into place and will stay still
while you solder them. Even so, make sure that they
are flush against the circuit board. There are outlines
on the board for both 1/4 inch and 1/8 inch jacks.
The transformers have a primary
and a secondary side, so the direction that it is inserted
into the circuit board is important. The primary side is
marked on the transformers with a “P”. You will also
notice that, on top of the transformer, the primary side is
white, while the secondary side is gray. The primary
side is marked on the circuit board with a white dot.
Insert the six wires of each transformer into the
corresponding holes, then press the two tabs into the
mounting holes. Apply gentle steady pressure until the
transformer tabs squish into the holes.
The tabs can be folded over on the underside of
the board if you like, and they do not need to be
soldered.
The pads for the battery
connector wires are marked on the circuit board with
“V+” and “GND”. The red wire is positive and the black
wire is negative (ground).
To help prevent the wires from accidentally getting
pulled out of the board, there is a strain relief hole. The
battery connector wires are first threaded up (or down)
through the hole next to the battery pads, arched over,
then soldered in place. This keeps the battery wires
from getting accidentally pulled out of the board. The
wires fit tightly, so it may help to crimp the insulation on
the wires before pushing them
If you intend to rack-mount the Ring Modulator, you can
The power
connection on the board is a 10-pin
The kit also includes various hardware
including: 1 switch cap, 2 potentiometer knobs,
2 nuts and 2 for the
potentiometers.
The 1
µF
Solder the six
leads.
The two 100K potentiometers are
inserted with the shaft facing away from the circuit
board. Make sure that they are seated flush against the
circuit board, particularly side-to-side. You may want to
tape them down while you solder them since they do
not snap into the board.
through the strain relief
hole.
use the rack’s power bus instead of a 9V battery. The
Ring Modulator (technically the internal oscillator)
works equally well with 9, 12 or 15 volts.
Doepfer-style
power header common in Eurorack standard modules.
3 nuts
for the jacks and washers
2 Potentiometers: