Inovonics FA200W - Manual

FA200W
Frequency Agile™ 900MHz
Universal Widegap Transmitter
User Manual
FA200W
Frequency Agile™ 900MHz
Universal Widegap Transmitter
User Manual
For technical support
or application assistance, call
800-782-2709 option #5
Inovonics Corporation
2100 Central Avenue
Boulder CO 80301
LIT-FA200W-USER Rev 2.00 25-Aug-00
For technical support
or application assistance, call
800-782-2709 option #5
Inovonics Corporation
2100 Central Avenue
Boulder CO 80301
LIT-FA200W-USER Rev 2.00 25-Aug-00
External contacts: N/O or N/C, as needed
N/O contacts: 30K Ω, minimum
N/C contacts: 80 Ω, maximum
(Requires 1.5 sec switch trigger, minimum)
(10 feet max from contact to transmitter)
Internal contacts: Yes, if using widegap
Typical battery life: 3 years
Battery type: 4.5V alkaline battery pack
Battery part #: BAT601
NOTE: Do not mount transmitters on doors. On metal doors, use external
contact designed for metal.
External contacts: N/O or N/C, as needed
N/O contacts: 30K Ω, minimum
N/C contacts: 80 Ω, maximum
(Requires 1.5 sec switch trigger, minimum)
(10 feet max from contact to transmitter)
Internal contacts: Yes, if using widegap
Typical battery life: 3 years
Battery type: 4.5V alkaline battery pack
Battery part #: BAT601
NOTE: Do not mount transmitters on doors. On metal doors, use external
contact designed for metal.
FA200W Programming
1. If no external sensor is used, program external contact loop as N/O, Internal Contact
(INT CNTCT) as "Yes".
2. When prompted to plug in transmitter, connect cable from programming device to
programming port on transmitter.
3. Press reset button on transmitter.
4. When programming is complete, disconnect cable.
NOTE: The FA200W retains programming data in non-volatile memory.
It does not require re-programming after loss of power. Install
new battery pack and press reset button to re-initialize the
transmitter and restore programming.
FA200W Programming
1. If no external sensor is used, program external contact loop as N/O,
Internal Contact (INT CNTCT) as "Yes".
2. When prompted to plug in transmitter, connect cable from programming device to
programming port on transmitter.
3. Press reset button on transmitter.
4. When programming is complete, disconnect cable.
NOTE: The FA200W retains programming data in non-volatile memory.
It does not require re-programming after loss of power. Install
new battery pack and press reset button to re-initialize the
transmitter and restore programming.
E xte rn a l c o nta c t te rm in a ls
In te rn a l re ed s w itc h
(o n P C B )
P ro g ra m m in g p o rt R e se t b u tto n Tam p e r s w itc h B a tte r y te rm in a ls
+
-
+
-
4.5V B a tte r y
A lig n m a g n et w ith tran s m itte r h o u s in g a s s h o w n.
M a xim u m m a g n e t
is 1 ”. tra n s m itte r– g a p
M a g n et
E xte rn a l c o nta c t te rm in a ls
In te rn a l re ed s w itc h
(o n P C B )
P ro g ra m m in g p o rt R e se t b u tto n Tam p e r s w itc h B a tte r y te rm in a ls
+
-
+
-
4.5V B a tte r y
A lig n m a g n et w ith tran s m itte r h o u s in g a s s h o w n.
M a xim u m m a g n e t
is 1 ”. tra n s m itte r– g a p
M a g n et