Inovonics EN1941 - Manual (Page 3)

4.9.13 06287E © Inovonics, 2013 - www.inovonics.com 3
7 Compliance Requirements
7.1 UL and cUL Requirements
The EN1941 Module holds a UL and cUL Recognized Component Mark
and is intended to be factory installed in another device, system or end-
product. The suitability of the EN1941 module for use in a UL and/or cUL
listed (certified) device, system or end-product, is restricted as follows:
• This device was evaluated as a UL/cUL Recognized Component
compliant to selected requirements from UL639, ULC-S306-03,
UL1076, ULC/ORD-C1076 and UL1610 as specified in the Conditions
of Acceptability of the UL Report.
• The Supply Line Transient tests shall be added to the RAC UL
evaluation program if it is powered by an AC/DC adapter rather than a
low voltage battery.
• If intended use includes UL1610, UL1076 or UL639 installations, the
RAC shall be evaluated for Short Range RF Device tests.
• Compatible receivers include EN4216MR, EN4232MR and EN7285.
Refer to the EN4216MR Installation and Operation Manual, the
EN4232MR Installation and Operation Manual or the EN7285
Installation Instructions.
• When selecting frequency band, only devices set for use in North
America are configured for UL and cUL installations.
7.2 FCC Requirements for the EN1941
The EN1941 one-way binary RF module has received a Limited Modular
Grant, requiring Inovonics to retain control of the final installation to ensure
compliance to FCC/IC regulations. The integrator is responsible to test the
final installation to verify compliance to FCC/IC regulation for unintentional
emissions.
Prior to marketing the product, the integrator must complete and submit to
Inovonics a compliance review form and documentation, and, if requested,
a functional product sample for approval. If this is not possible, the
integrator must perform the testing themselves and submit proof to
Inovonics of compliance to Part 15 of the FCC Rules and Industry Canada
RSS-210.
At the end of this guide is an Inovonics compliance review form to be filled
out by the integrator.
The integrator is also responsible for properly labeling the product
containing the one-way binary RF module. Labels must be placed on the
outside of the product, and must include a statement indicating that the
product contains the module, along with the FCC and IC number.
Example 1 “Contains One-Way Binary RF Module
FCC ID: HCQ3B6OT9OEM; IC ID: 2309A-OT9OEM (EN1941-IC)”
Example 2 “Contains FCC ID: HCQ3B6OT9OEM; IC ID: 2309A-OT9OEM
(EN1941-IC)”
7.3 Television and Radio Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
8 FCC Part 15 and Industry Canada Compliance
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
8.1 CE Label Requirements for EE1941
Inovonics Wireless has received European Telecommunications Standards
Institute approval to market one-way binary RF modules, and they are
manufactured to be RoHS compliant. The integrator is responsible for
properly labeling the product containing the one-way binary RF module.
Labels must be placed on the outside of the product, and must include the
CE logo.
9 Warranty and Disclaimer
Note: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Inovonics Wireless Corporation ("Inovonics") warrants its EchoStream
products ("Product" or "Products") to conform to its own specifications and
to be free of defects in materials and workmanship under normal use for a
period of thirty-six (36) months from the date of manufacture. Within the
warranty period, Inovonics will repair or replace, at its option, all or any part
of the warranted Product. Inovonics will not be responsible for dismantling
and/or reinstallation charges. To exercise the warranty, the User ("User",
"Installer" or "Consumer") must work directly through their authorized
distributor who will be given a Return Material Authorization ("RMA")
number by Inovonics. Details of shipment will be arranged directly through
the authorized distributor.
This warranty is void in cases of improper installation, misuse, failure to
follow installation and operating instructions, alteration, accident or
tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other warranties,
obligations or liabilities, whether written, oral, express, or implied. There is
no warranty by Inovonics that Inovonics product will be merchantable or fit
for any particular purpose, nor is there any other warranty, expressed or
implied, except as such is expressly set forth herein. In no event shall
Inovonics be liable for an incidental, consequential, indirect, special, or
exemplary damages, including but not limited to loss of profit, revenue, or
contract, loss of use, cost of down time, or interruption of business, nor any
claim made by distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics does not
authorize any person to act on its behalf to modify or extend this warranty.
This warranty will apply only to Inovonics Products. Inovonics will not be
liable for any direct, incidental, or consequential damage or loss
whatsoever, caused by the malfunction of Product due to products,
accessories, or attachments of other manufacturers, including batteries,
used in conjunction with Inovonics Products.