Jaclo Contempo grab bar - G80-**- User Manual

Page 3

Advertising
background image

Installation Instructions for Angular Grab Bars:
1 › Mark center of holes for mounting screws.
2 › Drill 1/8" diameter holes.
3 › Place escutcheon on post hubs and place on wall.

Drive #14 x 3" screw into 1" plywood or wood stud,
DO NOT TIGHTEN.

Note: Soap applied to screw

threads will reduce the power required.

4 › Repeat for other side.
5 › Make sure grab bar is aligned properly, then tighten

all srews.

6 › Install press caps.

7 › Install handshower if supplied.

JACLO.COM

GRAB BARS | PG 3

JACLO PROduCT CARe:
Thank you for selecting a JACLO product. In order to maintain the high quality finish of the product you have purchased,
please adhere to the following product care instructions:
Cleaning metal parts: For routine cleaning simply use a soft damp cloth and common household soap, then rinse and
dry. Proper care of your product is important because most water contains calcium that deposits on surfaces, forming
unpleasant spots. This can be avoided by routine cleaning and drying after every use. Use only mild soap based detergents.
Never use abrasive cleaners, disinfectants or cleaning products containing alcohol, ammonia, hydrochloric or
phosphoric acids as they will damage the product finish.
Please note:
Your product warranty may not be valid if the above cleaning guidelines are not followed.

LIMITed LIFeTIMe WARRANTY:
Your new plumbing fixture is warranted by JACLO INDUSTRIES, 129 Dermody Street, Cranford, NJ 07016. This warranty is
extended to original consumer purchasers only. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
The fixture (including the finish on the fixture but excluding any installation hardware not supplied by JACLO) is warranted
to be free from defects in material or workmanship under normal use and service for the lifetime of the fixture, so long as
the original consumer purchaser owns it. JACLO’s sole obligation under this or any other warranty is limited to repairing or
replacing, at JACLO’s option, any part or parts of the fixture which fail to conform to such warranty. JACLO WILL NOT BE
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES caused by a breach of this or any other warranty.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may
not apply to you.
In order to secure warranty performance, the original consumer purchaser must (a) have the fixture properly installed in
accordance with all installation instructions, (b) not subject the fixture to abuse, misuse or alter it in any way, and (c) remove
the fixture and return it to JACLO, transportation prepaid, together with a brief description of the defect.
JACLO does not authorize any distributor, retailer or other person to modify this warranty or assume any liability on its
behalf with respect to it. Any questions regarding the operation of warranty should be addressed to JACLO, Warranty
Department.

Advertising
This manual is related to the following products:

Retro fit flange - G-ADAPTER, Drill bit for Luxury Grab Bar fastener - G-WBIT, 60" x 60 inside corner grab bar - G**-60-60-IC-", 48" x 60 inside corner grab bar - G**-48-60-IC-", 48" straight grab bar - G**-48-, 36" x 60 inside corner grab bar - G**-36-60-IC-", 36" x 36 inside corner grab bar - G**-36-36-IC-", 32H x 16W 90° grab bar - G**-32H-16W-, 32" x 60 inside corner grab bar - G**-32-60-IC-", 32" x 36 inside corner grab bar - G**-32-36-IC-", 32" straight grab bar - G**-32-, 24H x 16W 90° grab bar - G**-24H-16W-, 24" x 60 inside corner grab bar - G**-24-60-IC-", 24" x 36 inside corner grab bar - G**-24-36-IC-", 24" x 24 inside corner grab bar - G**-24-24-IC-", 18" straight grab bar - G**-18-, 16H x 24W 90° grab bar - G**-16H-24W-, 16H x 12W 90° grab bar - G**-16H-12W-, 16" x 48 inside corner grab bar - G**-16-48-IC-", 16" x 32 inside corner grab bar - G**-16-32-IC-", 16" x 16 inside corner grab bar - G**-16-16-IC-", 12H x 32W 90° grab bar - G**-12H-32W-, 12H x 16W 90° grab bar - G**-12H-16W-, 12" x 60 inside corner grab bar - G**-12-60-IC-", 12" x 36 inside corner grab bar - G**-12-36-IC-", 12" x 24 inside corner grab bar - G**-12-24-IC-", 12" x 12 inside corner grab bar - G**-12-12-IC-", Between stud mounting hardware (For luxury grab bars only) - G-WING, 60" straight grab bar - G**-60-, 48" x 48 inside corner grab bar - G**-48-48-IC-", 42" straight grab bar - G**-42-, 36" x 48 inside corner grab bar - G**-36-48-IC-", 36" straight grab bar - G**-36-, 32H x 32W 90° grab bar - G**-32H-32W-, 32H x 24W 90° grab bar - G**-32H-24W-, 32H x 12W 90° grab bar - G**-32H-12W-, 32" x 48 inside corner grab bar - G**-32-48-IC-", 32" x 32 inside corner grab bar - G**-32-32-IC-", 24H x 32W 90° grab bar - G**-24H-32W-, 24H x 24W 90° grab bar - G**-24H-24W-, 24H x 12W 90° grab bar - G**-24H-12W-, 24" x 48 inside corner grab bar - G**-24-48-IC-", 24" x 32 inside corner grab bar - G**-24-32-IC-", 24" straight grab bar - G**-24-, 16H x 32W 90° grab bar - G**-16H-32W-, 16H x 16W 90° grab bar - G**-16H-16W-, 16" x 60 inside corner grab bar - G**-16-60-IC-", 16" x 36 inside corner grab bar - G**-16-36-IC-", 16" x 24 inside corner grab bar - G**-16-24-IC-", 16" straight grab bar - G**-16-, 12H x 24W 90° grab bar - G**-12H-24W-, 12H x 12W 90° grab bar - G**-12H-12W-, 12" x 48 inside corner grab bar - G**-12-48-IC-", 12" x 32 inside corner grab bar - G**-12-32-IC-", 12" x 16 inside corner grab bar - G**-12-16-IC-", 12" straight grab bar - G**-12-