American Access Systems Advantage DKLP - Single Gang - 19-100sg - Manual (Page 5)

Page 5 American Access Systems / Security Brands, Inc.
THE MAsTER CODE AND ACCEss CODEs
Depending on which model you have, your unit may be programmed with multiple (4 digit) ACCEss CODEs, the
number of access codes is reflected in the model number (eg. 19-100(i) = 100 access codes.). The MAsTER CODE is a
4 digit programmable code used for accessing the program mode.
Note: The model number of the unit is located on the inside face of the unit.
sETTING OR REsETTING THE MAsTER CODE
To set or reset the master code back to the factory default of 1 2 5 1 should you ever loose or forget you master code.
To do this follow these steps: (SEE PAGE 7 FOR LOCATION DIAGRAM)
(1). Disconnect power from the unit by pulling the power harness away from the board.
(2). Reconnect power while holding down the PROGRAM/RESET button.
(3). A single keybeep will be heard from the unit indicating that the master has been reset
GOODBEEPs AND ERRORBEEPs
A standard beep will be heard each time a key is pressed. A “GOODBEEP” is represented by a series of quick beeps
in succession. An “ERRORBEEP” is represented by a single long beep.
THE IDLE MODE
The idle mode is the normal mode of operation. When in this mode the unit sits and waits for data from the keypad.
If a key is pressed from the keypad, you will have approximately 3 seconds between each keypress before the unit
resets.
THE PROGRAM MODE
The program mode is the mode of operation in which you will enter/change your access code. Upon entry, a
GOODBEEP will heard. A GOODBEEP will also be heard when you exit the program mode unless a keypress timeout
occurs in which case you will receive an ERRORBEEP. The program mode is accessed by entering the “MASTER CODE”
from the keypad. If the master code is valid, you will receive a GOODBEEP from the unit. In this mode you will have
approximately 15 seconds between keypresses. If this time is exceeded, you will receive an ERRORBEEP and the unit
will exit the program mode and return to the idle mode. To exit the program mode at any time, press #.
THE * AND # KEYs
The * and # keys serve specific functions while in the idle or program mode. The * key is always the clear key. You
should use this key if you make an entry error. The # key also serves as the clear key in the idle mode. In the program
mode however, it serves as the exit key and will at any time when depressed, exit you from the program mode.
PROGRAMMING
A person desiring a access to the program mode will enter the present MASTER CODE. If the master code is valid a
GOODBEEP will be heard prompting the person to enter a number corresponding to the SUB-MODE, eg. (MASTER
CODE) + (Number corrresponding to Sub-Mode). Once in the program mode the individual will have approximately
15 seconds between keypresses or the unit will sound an ERRORBEEP and exit the program mode. NOTE: An access
code log sheet is provided on page 8 which can be photo-copied. A good source for access codes is the phone
book or the last 4 digits of social security numbers.
sUB-MODEs
“1”
sub-Mode 1 (Enter New Access Codes)
To enter new access codes enter the MASTER CODE, followed by 1, then enter each new ACCESS CODE you wish to
program into the unit.
(MAsTER CODE) + 1 + (ACCEss CODE) + (ACCEss CODE) etc... (# to exit)
Should you make an entry error, simply press the * key and re-enter the correct data. You may continue entering
access codes until the memory is full or the # is pressed. You may select any 4 digit access code that is not already in
use by the system. The unit will respond with a GOODBEEP with the acceptance of each new access code. If you do
not receive a GOODBEEP after the entry of an access code, you must select a new access code as it is already in use
by the system. When the memory becomes filled, you will receive a GOODBEEP indicating the acceptance of the
last access code entered and then the unit will sound an ERRORBEEP and automatically exit you from the program
mode.
NOTE: You will not be able to enter this mode if memory is full and will receive an ERRORBEEP.
“2”
sub-Mode 2 (Delete Access Codes)
To delete any access code from memory enter the MASTER CODE, followed by 2, and then each access code to be
deleted
(MAsTER CODE) + 2 + (CODE TO BE DELETED) + (NEXT CODE TO BE DELETED) etc... (# to Exit)
Should you make an entry error, simply press the * key and re-enter the correct data. You may continue deleting
access codes in a successive manner. The unit will respond with a GOODBEEP with the successful deletion of each
access code. If you do not receive a GOODBEEP the access code entered could not be found in memory and the
unit will wait for you to enter another code to be deleted.