Campbell Hausfeld NS2190 - Manual (Page 2)

2
use. Always reconnect the air line
BEFORE loading any fasteners. The
nailer could eject a fastener causing
death or serious personal injury.
● Protect your eyes and ears. Wear
Z87 safety glasses,
with side shields.
Wear hearing
protection. Employers
and users are
responsible for
ensuring the user or anyone near
the nailer wears this safety
protection. Serious eye injury or
permanent hearing loss could
result.
● Do not use a
check valve or
any other fitting
which allows air
to remain in the
nailer. Death or
serious personal injury could occur.
● Never place
hands or any
other body parts
in the nail
discharge area
of the nailer.
The nailer might
eject a fastener and could result in
death or serious personal injury.
● Never carry the
nailer by the air
hose or pull the
hose to move the
nailer or a
compressor. Keep
hoses away from
heat, oil and sharp edges. Replace
any hose that is damaged, weak or
worn. Personal injury or tool
damage could occur.
● Always assume the nailer contains
nails. Never use the nailer as a toy.
Do not engage in horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Never point the
nailer at anyone. Accidental
triggering of the nailer could result
in death or serious personal injury.
● Do not drive a
nail on top of
other nails. The
nail could glance
and cause death
or a serious
puncture wound.
● Do not operate
or allow anyone
else to operate
the nailer if any
warnings or
warning labels
are not legible.
Warnings or warning labels are located
on the nailer magazine and body.
● Never leave the nailer unattended or
connected to an air compressor when
not in use. Serious personal injury
can occur if someone picks up and
uses the nailer without knowing the
correct way to operate the nailer.
● Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
Caution indicates a
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
● Do not modify or alter the nailer or
any nailer parts. Do not use the nailer
if any shields or guards are removed
or altered. Do not use the nailer as a
! CAUTION
hammer. Personal injury or tool
dam.occur.
● Avoid long extended periods of work
with the nailer. Stop using the nailer
if you feel pain in hands or arms.
● Always check
that the
Work Contact
Element
(WCE) is
operating
properly. A
nail could
accidentally
be driven if
the WCE is not working properly.
Personal injury may occur (See
"Checking the Work Contact
Element" Section).
● Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
● Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
● Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
● Air compressors providing air to the
nailer should follow the
requirements established by the
American National Standards
Institute Standard B19.3-1991;
Safety Standard for Compressors for
Process Industries. Contact your air
NOTICE
Models NS2190 & NS3490 Operating Instructions
! WARNING
NS2190 NS3490
• REQUIRES (SCFM with 16
nails per minute @ 90 psi) 4.1 4.1
• AIR INLET 1/4” NPT 1/4” NPT
• NAIL LENGTH RANGE 2” to 3 1 ⁄ 2 ” 2” to 3 1 ⁄ 2 ”
• NAIL SHANK RANGE 0.113” to 0.131” 0.113” to 0.131”
• MAGAZINE CAPACITY 60-75 75-105
• WEIGHT 8 lbs. 5 oz. 8 lbs. 11 oz.
• LENGTH 19.5” 19.75”
• HEIGHT 15” 15”
• MAXIMUM PRESSURE 120 psi 120 psi
• PRESSURE RANGE 70 - 120 psi 70 - 120 psi
Nailer Components And Specifications
7-Sp
Manual de Instrucciones Modelos NS2190 & NS3490
Adjustable Direction
Exhaust Deflector
Threaded Hole/Tool
Balancer (M8 x 1.25)
Nail Loading Area
Magazine
Single Cycle
Trigger
Warning Labels
Nail Discharge
Area
Work
Contact
Element
www.chpower.com
Notas