Avlink VH-EXWB - Manual (Page 2)

Installation
1. Turn off the DVD PC and HDTV.
2. Connect the HDMI extension cable between the DVD
and the “HDMI IN” port of VH-ELWB.
3. Connect the VGA extension cable between the PC and
the “VGA IN” port of VH-ELWB.
4. Connect the AUDIO extension cable between the PC
and the “AUDIO IN” port of VH-ELWB.
5. Connect the HDMI extension cable between the HDTV
and the “HDMI OUT” port of VH-ELWB.
6. Connect the CAT.5 cables between the VH-ELWB
“LINK” port and the VH-ERWB “LINK” port of extender.
7. Connect the power cord and turn on the extender.
8. Turn on the DVD and HDTV.
9. Select source (HDMI/VGA) by TACK SW or 1X2 pole
captive screw (short).
IR Receiver Cable Directions:
Put it into the VH-ERWB “IR IN” port and place the IR
Receiver Cable, so that you can point to it easily with your
IR remote controller.
IR Blaster Cable Directions:
Plug IR blaster cable plug into VH-ELWB “IR OUT” port, It
sits in front of the DVD receiver’s IR sensor, which is
located on the front-panel.
DIP Switch Setting
VH-ELWB:
BIT 1~2: F/W UPGRADE
OFF, OFF  NORMAL
OFF, ON  REMOTE
ON, OFF  LOCAL
BIT 5~6: AUTO/MANUAL
OFF, OFF  NORMAL
OFF, ON  AUTO SENSING
ON, OFF  HDMI PRIORITY
ON, ON  VGA PRIORITY
BIT 7~8: DA MODE
OFF, OFF  SELECTED
OFF, ON  NON-SELECTED
ON, OFF  HDMI
ON, ON  VGA
VH-ERWB:
BIT 1~2: F/W UPGRADE
OFF, OFF  NORMAL
OFF, ON  LOCAL
ON, OFF  REMOTE
-3-
F/W UPGRADE
Process the Update TX_xxx.bat or UpdateRX_xxx.bat file
to upgrade firmware. (xxx is specified for firmware version)
These files are used for upgrading in your devices.
- The UpdateTX_xxx.bat file is used to upgrade the
Local firmware.
- The UpdateRX_xxx.bat file is used to upgrade the
Remote firmware.
Local Unit:
1. Connect the RS-232 cable between the PC and the
“RS-232” port of VH-ELWB.
2. Dip switch bit1 set “ON’, Running “TX_xxx.bat” file ,you
can upgrade VH-ELWB.
3. Dip switch bit2 set “ON’, Running “RX_xxx.bat” file ,you
can upgrade VH-ERWB.
Remote Unit:
1. Connect the RS-232 cable between the PC and the
“RS-232” port of VH-ERWB.
2. Dip switch bit1 set “ON’, Running “RX_xxx.bat” file ,you
can upgrade VH-ERWB.
3. Dip switch bit2 set “ON’, Running “TX_xxx.bat” file ,you
can upgrade VH-ELWB.
Additional Options
Select any additional options you may require.
1. IR Receiver Cable
GND
+V
Sig
2. IR Blaster Cable
NC
P+
N-
-4-
Technical Specifications Output Signal
Pin # Signal Pin # Signal
1 TMDS Data 2+ 11 TMDS Clock Shield
2 TMDS Data 2 Shield 12 TMDS Clock -
3 TMDS Data 2- 13 CEC
4 TMDS Data 1+ 14
Reserved
(N.C. on device)
5 TMDS Data 1 Shield 15 SCL
6 TMDS Data 1- 16 SDA
7 TMDS Data 0+ 17 DDC/CEC Ground
8 TMDS Data 0 Shield 18 +5 Power
9 TMDS Data 0- 19 Hot Plug Detect
10 TMDS Clock+
Wiring Information & Coding
Conductor
Identification
RJ45 Pin
Assignment
Color Code for
Conductor
Pair 1
5 White-Blue
4 Blue
Pair 2
1 White-Orange
2 Orange
Pair 3
3 White-Green
6 Green
Pair 4
7 White-Brown
8 Brown
-5-