Avlink VAX-8404F - Manual (Page 2)

Operation
1. When you press button “Out1“ or “Out2“ or “Out3“ or “Out4“,
the corresponding Out 7-Segment LED will start flashing for
3 seconds. There are total three switching methods:
a. a. Press button “In1“ or “In2“ or “In3“or “In4“ within 3
seconds to make 7-Segment LED stop flashing and
change its display to the number of Input port you set.
Then the Output port will switch to the corresponding
Input port.
b. b. Press button ”OFF” within 3 seconds to make
7-Segment LED stop flashing and display ”0”. Then this
Output port will be turned off.
c. c. If you don’t press any button within 3 seconds, the
7-Segment LED will stop flashing and keep displaying
original number and setting of Output port.
d. d. If you press button “Out1“ or “Out2“ or “Out3“ or
“Out4“ within 3 seconds, then Out 7-Segment LED will
start flashing for 3 seconds again to wait for button
“In1“ or “In2“ or “In3“ or “In4“, “OFF” pressed.
2. When you press button ”All”, all 7-Segment LED will start
flashing for 3 seconds. There are total three switching
methods:
a. Press button “In1“ or “In2“ or “In3“or “In4“ within 3
seconds to make all 7-Segment LED stop flashing and
change their displays to the number of Input ports you
set. Then all Output ports will switch to the
corresponding Input ports.
b. Press button ”OFF” within 3 seconds to make all
7-Segment LED stop flashing and display ”0”. Then all
Output ports will be turned off.
c. If you don’t press any button within 3 seconds, all
7-Segment LED will stop flashing and keep displaying
original number and setting of Output port.
d. If you press button “All“ within 3 seconds, then all Out
7-Segment LED will start flashing for 3 seconds again to
wait for button “In1“ or “In2“ or “In3“ or “In4“, “OFF”
pressed.
Note:
ƒ
When video/audio matrix is connected to power supply, the
initial setting of jack connection is: ”Out1” to ”In1”, ”Out2”
to ”In2”, ”Out3” to ”In3”, ”Out4” to ”In4”.
ƒ If you install DDC monitor for video/audio matrix, then the
setting of DDC will be applied to the other monitors.
ƒ To get the functionality of DDC monitor, please connect the
following jacks: “Video In1” to “Video Out1”, “Video In2” to
“Video Out2”, “Video In3” to “Video Out3”, and “Video In4” to
“Video Out4”.
ƒ Available monitors include the VGA, SVGA, UXGA, QXGA,
Multisync, and exclude the CGA, EGA, Mono.
-3-
Operation for cascade:
1. The function to display image on more monitors, you
request to attach another video/audio matrix or the
standard video/audio splitter.
2. Connect the HD-15 male/male video extension cable
between the “Video Out” port of the former video/audio
matrix and the “Video In” port of the latter video/audio
matrix.
3. Connect the 3.5φ Stereo plug male/male audio extension
cable between the “Audio Out” port of the former
video/audio matrix and the “Audio In” port of the latter
video/audio matrix.
Note:
Even though you are allowed to cascade the video/audio
matrix with varied ports, the image might become unstable
if cascade too many tiers of video/audio matrixes.
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or
registered trademarks belonging to their respective
companies.
-4-