Awntech Charleston Series - Manual (Page 2)

THESE AWNINGS ARE DESIGNED 4-1/2” WIDER THAN THE OPENINGS
YOU ARE COVERING. (EXAMPLE: CH22-5 is for a 5’-0” wide window. It is built
64-1/2” wide, 31” tall including 7” valance and 36” projection (deep).
Due to the wide variety of building surfaces, Awntech does not supply
the hardware to install your awning on the wall. You will need to
purchase installation hardware at your local do-it-yourself center. We
will advise you on different surface applications.
CONCRETE BLOCK WALLS: (1) ½” masonry bit with a 3/8” shank, (4-5) 5/16”x 3”
masonry anchor bolts, 9/16” socket. You will also need a roll of weather stripping.
METAL BUILDINGS: (1) 2x6x8 #2YP cut into 12” blocks for the back side of the
metal, (4-5) 5/16”x 4” lag bolts, (4-5) 5/16” washers, rubber installation strips (in the
shape of the metal) and a 3/8” drill bit. Bolt through the washer, the bracket and the
metal into wood blocks behind the metal. Before tightening the bracket insert the rubber
strips between the building and the awning.
ANY TYPE OF SIDING: (4-5) ¼”x 4” toggle bolts, (4-5) ¼” washers, (1) Flat head
screwdriver (1) ½ drill bit (or if you hit a stud): (5-8) 5/16”x4” lag bolts, (4-5) 5/16”
washers, (1) 3/16” drill bit and a 9/16” socket. You will also need a roll of weather
stripping.
CONCRETE, BRICK OR STONE: (1) ½ masonry bit with a 3/8” shank, (4-5) 5/16”x
3” masonry anchor bolts, (4-5) 5/16”x1/4” bushings, 9/16” socket. You will also need a
roll of weather stripping.
STUCCO: (4-5) ¼”x 4” toggle bolts, (4-5) ¼” washers, (1) Flat head screwdriver (1) ½
drill bit (or if you hit a stud): (4) 5/16”x4” lag bolts, (4-5) 5/16” washers, (1) 3/16” drill
bit and a 9/16” socket. You will also need a roll of weather stripping
.
• Please read the instructions fully before assembly.
• This awning is designed to be assembled on the wall.
Size 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
(TB) Top Bar - C Channel 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2
(FB) Front Bar 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2
(NC) Hypotenuse / Cover
Support
2 2 2 3 3 3 4 4 5 5 5 5 5 7 7 7 7 7
(AA) Architectural Arms 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
(BP) Black Projection Bar 0 0 0 1 1 1 2 2 3 3 3 3 3 5 5 5 5 5
Other parts Self tapping screws, Z-brackets
Tools Required: Electrical Drill, ¼” Nut Driver Bit, Full Socket Set, Full set of Steel
and Masonry Bits, Tape Measure, Safety Glasses, 4’ Level, A Safe Ladder, #2 Pencil
YOU MAY ALSO NEED A HELPER DEPENDING ON THE SIZE, WEIGHT, LENGTH
AND HEIGHT OF THE AWNING