Bike2Power Power Plus Pack for Galaxy S4/S3 - Manual (Page 2)

2. Installation
A. 1. Pull the 2 side levers from the bottom of the case.
2. Open the 2 side latches.
3. Pull the lower latch out a bit to lift up the front cover.
B. 1. Use a screw driver to loosen the 2 Phillips screws on the lower end of the case.
2. Discard the 2 screws.
3. Remove the plastic cover.
4. In place of the plastic cover, insert the micro USB connector module (1.B.). Ensure the 2
cables coming out from the lower end of the module stay in the groove.
5. Insert the 2 longer Phillips screws coming with the package (1.C.) into the module.
6. Use a screw driver to tighten the module in the case.
C. Gently tilt the micro USB connector up by not more than 5˚.
D. 1. Tilt the phone and gently insert it into the micro USB connector.
2. Push the rest of the phone in until it fits snugly inside the silicone liner.
E. 1. Close the front cover.
2. Position the 2 side latches on the grooves of the cover.
3. Push the 2 side levers down until the front cover is locked.
F. 1. Push the battery pack towards the back of the BikeConsole until the 4 prongs sink inside
the trough.
2. Push the battery pack forward until the 4 prongs lock in place.
3. Turn the knob clockwise until the battery pack is firmly locked in place.
G.1. Place the whole unit on the mounting bracket until the 4 prongs get into the trough at the
back of the battery pack.
2. Slide the whole unit backward until the Quick Release locks in.
3. Turn the knob clockwise until the whole unit is firmly locked in place.
H. Push the power button on the battery pack once to start charging the phone. Push again
to stop.
I. 1. Open the Power IN cap for charging the battery pack. Open the Power OUT cap for using
the battery pack to charge other devices.
2. Screw in the 2.5mm DC connector of the Power In cable to the Power IN port, and connect
the USB connector at the other end of the cable to a compatible power source for charging
the battery pack. Plug in the micro USB connector of the Power Out cable to the Power OUT
port, and plug in the charging cable of the other device to the female USB connector at
the other end of the cable to charge the device with the battery pack. To start charging,
push the power button once.
3. Rotate the Power In cable clockwise to fix it firmly on the Power IN port.
X
1. C.
1 1
2 2
3
A B C
D E
H
F
G I
1
2
3
4
5
6
<5°
1
2
1
2 2
3 3 1
2 3
1
2
3
1
1
2
2
3
2. Installation
A. 1. Pull the 2 side levers from the bottom of the case.
2. Open the 2 side latches.
3. Pull the lower latch out a bit to lift up the front cover.
B. 1. Use a screw driver to loosen the 2 Phillips screws on the lower end of the case.
2. Discard the 2 screws.
3. Remove the plastic cover.
4. In place of the plastic cover, insert the micro USB connector module (1.B.). Ensure the 2
cables coming out from the lower end of the module stay in the groove.
5. Insert the 2 longer Phillips screws coming with the package (1.C.) into the module.
6. Use a screw driver to tighten the module in the case.
C. Gently tilt the micro USB connector up by not more than 5˚.
D. 1. Tilt the phone and gently insert it into the micro USB connector.
2. Push the rest of the phone in until it fits snugly inside the silicone liner.
E. 1. Close the front cover.
2. Position the 2 side latches on the grooves of the cover.
3. Push the 2 side levers down until the front cover is locked.
F. 1. Push the battery pack towards the back of the BikeConsole until the 4 prongs sink inside
the trough.
2. Push the battery pack forward until the 4 prongs lock in place.
3. Turn the knob clockwise until the battery pack is firmly locked in place.
G.1. Place the whole unit on the mounting bracket until the 4 prongs get into the trough at the
back of the battery pack.
2. Slide the whole unit backward until the Quick Release locks in.
3. Turn the knob clockwise until the whole unit is firmly locked in place.
H. Push the power button on the battery pack once to start charging the phone. Push again
to stop.
I. 1. Open the Power IN cap for charging the battery pack. Open the Power OUT cap for using
the battery pack to charge other devices.
2. Screw in the 2.5mm DC connector of the Power In cable to the Power IN port, and connect
the USB connector at the other end of the cable to a compatible power source for charging
the battery pack. Plug in the micro USB connector of the Power Out cable to the Power OUT
port, and plug in the charging cable of the other device to the female USB connector at
the other end of the cable to charge the device with the battery pack. To start charging,
push the power button once.
3. Rotate the Power In cable clockwise to fix it firmly on the Power IN port.
X
1. C.
1 1
2 2
3
A B C
D E
H
F
G I
1
2
3
4
5
6
<5°
1
2
1
2 2
3 3 1
2 3
1
2
3
1
1
2
2
3