Blinds Chalet Silverscreen Roller Shades - 4% - Manual

Extension Brackets (optional for Headrail shades)
Optional Extension Brackets are used to project the back of the
shading up to 2 1/2" from the mounting surface. Attach the Standard
Mounting Bracket to the Extension Bracket with the nut and bolt
provided.
Side Mount (optional for Headrail shades)
Measure from window sill up to desired mounting position on each
side of the window frame. Mark position. Mount Side Mount Brackets
on each side of window frame as shown. Make sure to confirm that
headrail will sit perfectly level. Once Side Mount Brackets are
installed and properly positioned, attach the Standard Mounting
Brackets using the nuts and bolts provided.
Step 2. HANGING THE SHADE
Shades with NO Headrail or Fascia
Once the brackets are secured and level, the fabric roll can be
inserted. Make sure your hands are clean to avoid soiling the fabric.
While facing the inside of the shade, be sure the clutch and roller end
plug are inserted into the roller. Hold the
shade with the bottom of the clutch facing
the floor, and the beaded cord hanging
straight down.
Insert the foot of the control-
side bracket into the slotted
center hole of the clutch. Set
nub of the end plug into the V
of the support bracket.
Rotate the T-hook on the
support bracket to engage
over the nub on the idler and
secure the fabric roll.
Inside Mount - Fascia or NO Headrail
Inside Mount with Headrail
Fully Recessed Inside Mount with Deluxe Headrail
Outside Mount - Fascia or NO Headrail
Outside Mount - with Headrail
Extension and Sidemount - NO Headrail
The standard roller brackets can be mounted to the side of any
opening utilizing the holes in the side of the bracket.
The optional Extension roller brackets mount in the same manner as
above, but allow an extra 1/2” of projection for the roller.
BASICS
A few simple tools are required:
- Measuring tape
- Carpenters Level
- Power drill or Phillips head Screwdriver
- ¼" Hex head and/or Phillips driver bit
Additional fasteners other than those sent with your shading may be
required depending on the mounting surface. Wallboard and plaster require
the use of anchors such as expansion or toggle bolts. Brick, tile or stone
need special plugs and drill bits. Remember to always pre-drill holes in
wood to avoid splitting.
Step 1. BRACKET INSTALLATION
For shades with headrail, the End brackets
should be located with centerlines 2" in from
each end. Depending on the width of the
shading, necessary additional brackets may
be evenly spaced between the two end
brackets.
For shades with NO headrail, the installation brackets are always
mounted so that the inner surfaces face each other. For Shades with
a fascia, the brackets are mounted with the open end down. It is very
important that the
brackets are
mounted so that
the shade is level
when installed.
1 1/4” Hex
Head
Bracket
Screw
Deluxe
Mounting
Bracket
Wedge for Deluxe
Headrail Bracket
Headrail Extension &
Side mount Bracket
Nut &
Bolt
“U” Shim for
Headrail bracket
Hold Down Bracket
(optional)
Hold Down
Bracket Screw
If the headrail or roller does not sit level, the fabric will not roll up
evenly which could damage the edges of the shading fabric.
Mount roller brackets as necessary, or use shims for headrail
shades if necessary to level brackets.
Low light gap wedges can be used to reduce the
top light gap when the shade is mounted fully
recessed. The wedge is placed between the
mounting surface and the bracket with the tabs
on the wedge facing down and the thick end of
the wedge toward the back of the bracket.
3/4” minimum surface
Shade width # Brackets
Up to 40” 2
>40” - 72” 3
>72” - 84” 4
>84” - 114” 5
Roller Mounting
Brackets for NO Headrail
The roller brackets
can be mounted up
against the window
frame, or back
against the window
casing.
Foot
T-Hook
The roller brackets
can be mounted
back against the
window casing, or
up against the
ceiling.
Control Side
Bracket
End Plug Side
Bracket
Nub
Support Bracket
Ultra Sleek
Mounting
Bracket
3/4” minimum surface
2 1/2” 2 1/2”
2” minimum surface required
Position screw in center of slot
so you can adjust position of
bracket as necessary.
Ultra Sleek Deluxe
Ultra Sleek Deluxe
1” minimum for
shallow mount
2 7/8” minimum for
flush inside mount
Use shims if necessary to ensure that the headrail is mounted level (included).
3/4” minimum for
shallow mount
3 3/4” minimum for
flush inside mount
2”
2”
Brackets for Roller
Shades with Fascia
T-Hook
Control Side
Bracket
End plug Side
Bracket
No Headrail
bracket pictured
Ultra Sleek Deluxe
Fascia
No Headrail
Fascia
No Headrail
Ultra Sleek
Deluxe