While dishwasher is running, Electrical connection, Converting to built-in – Whirlpool DP3000XR Series User Manual

Page 14: Caring for simulated wood top, Connecting your portable dishwasher, When cycle is finished, Before starting

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

Connecting your portable dishwasher

A special adapter must be installed on the faucet before the dishwasher can

be connected. Complete instructions and the adapter are packed with your
dishwasher.

When moving yourdishwasher, make sure the

door is latched. Hold the dishwasher at the top

front corners.

Before starting

1.

Run water at faucet until it is

hot.

Turn it off.

PULL RING

Pull hoses out of their storage compartment

on the back.

LOCKING COLLAR

Pull down on the locking collar while lifting

the hose connector onto the faucet adapter.

When the connector snaps into place, re­

lease the locking collar.

Turn the

hot

water on slowly until it is

all the

way on.

Plug in power supply cord.
See pages 8 and 9 to start the dishwasher.

While dishwasher is running

You can draw water from the faucet while the

dishwasher is connected.

DO NOT

draw water

while the dishwasher is filling or while water is

being pumped out. (This helps prevent a low fill
when dishwasher is filling, or mixing drain water

with fresh water.)

1. Press red button on hose connector to get

the water you want. (The faucet is set on hot.

Adjust faucet for the water you want.)

2. Be sure you return cold water to off, and

fhaf hot water Is full on.

When cycle is finished

Turn hot water off. (This can be done after the

iast rinse.)

Press the red button on the connector to re­
lease the water pressure.

Lift slightly on the hose connector while pull­
ing down the locking collar. Pull down on
the connector.

1

.

2

.

4. Empty any remaining water from the

connector.

5. Unplug power supply cord and return to

storage compartment.

6. Return hoses to storage compartment.

Electrical Connection

A power supply of 120 volts, 60Hz AC only, 15 or

20 amps, is required. For your personal safety,

this appliance must be grounded. This ap­
pliance is equipped with a power supply cord

having a 3-prong grounding plug. To minimize
possible shock hazard it must be plugged into a
mating 3-prong grounding type wall recepta­

cle, grounded in accordance with the National

Electrical Code and local codes and ordi­

nances. If a mating wall receptacle is not avail­
able, it is the personal responsibility and obliga­
tion of the customer to have a properly
grounded 3-prong wall receptacle installed by
a qualified electrician.

A

WARNING: An extension cord

should not be used with this ap­

pliance. Such use may result in a fire,

electrical shock or other personal injury.

3-Prong

Grounding Type

Wall Receptacle

3-Prong
Grounding
Plug

Power Supply Cord

DO NOT, UNDER ANY CIRCUMSTANCES, RE­
MOVE THE POWER SUPPLY CORD GROUND

PRONG.

Converting to built-in

Your Whirlpool Portable Dishwasher can be

converted to a built-in (undercounter) model
by using conversion kit No. 569056. The kit is
available at your Whirlpool dealer or autho­
rized TECH-CARE* Service Company. Instruc­

tions are included with the kit.

Caring for

simulated wood top

The simulated wood top can be used as a

utility work surface for most kitchen jobs. It is

stronger and more easily cleaned than genu­

ine wood.

The top can be used as a cutting board. Knife

marks will be visible but will not seriously
damage top. Hot items from the oven can be
placed on the top.

Clean with warm, soapy water. For dried-on

foods, use a scouring pad.

14

Advertising