GE 49-4992 - Manual (Page 11)

^ Auíomaíic Oven I'inier
^ The oven timer will automatically
start and stop your oven cooking or
|elf-cleaning operation for you.
For automatic oven cooking:
2. Turn SET knob to set length of
baking time.
3. Push BAKE button.
4. Turn SET knob to set desired
temperature.
When cook time is reached, the
End-of-Cycle Tone will sound and
the oven will turn off.
During automatic cooking:
® You can push the STOP TIME
button to find out when the End~of~
Cycle Tone will sound and the oven
will turn off.
® You can push the CLOCK button
todisplay time of day without
cancelling the oven operation.
^To Delay Starting an
^^utomatic Oven Operation
If a delayed cooking operation
isdesiredf
1. Push COOK TIME button.
2. Set length of baking time with
SET knob.
3. Push STOP TIME button.
4. Turn SET knob to time of day
when baking should be conipleted.
Stop time must be equal to or
greater than the cook time plus the
current time of day.
5. Push BA.KE button.
6. Turn SET knob to desired
temperature.
When stop time is reached, the
wiu duuiiu auu
the oven will turn off.
Caution: Never let food sit in the
oven for more than 4 hours before
cooking starts» Room temperature
is ideal for the growth of harmful
bacteria. Be sure oven light is off
because heat from the bulb will
speed bacteria growth.
Note; You can push the STOP
TIME button to find out when the
oven will turn off. Push and hold
the COOK TIME button to find out
ГЧЛ//ЛП Л1 /П1 turn r\ri
WllWli I.I1V/ V/VX.»!! Will (.UAIl Ч/1Д.
If a delayed self-cleaning oven
operation is desired, see page 21.
Function Error Tone (series of
very rapid beeps, 1/8-second on.
uiapittj mu* oiiwrv w,
failure code. Cancel Function Error
Tone by pushing the CANCEL
button. If the Function Error Tone
starts again (after about 15
seconds), call for service.
Disconnect the range electrical
__
sudd I v to stoD the tone.
------ r r - J ------------------------ r -------------- I..........................................................................................................
If the function error occurred ^ _
while you were programming the
Electronic Control, push the
CANCEL button and try again.
^
To Cancel the Tone... If you don’t ““
want an audible tone when you
push a button, you can eliminate
the Key Tone by pushing and
a IL j Y
ilUlUiilg UlC UUtlWll Ulliil
you hear a short beep (in
approximately two seconds). To
activate the tone again, push and
hold the CANCEL button once '
more until you hear a short beep.
Cancelling or activating the tone
should only be done when there is
no oven operation programmed.
Pushing the CANCEL button will
clear all functions except the Clock
and Minute/Second Timer.
How io Change
aPrc^ram
When a function has been
entered, you can recall what has
UUWU piV^glCUilliAWVft py'.pUOitillg .
the corresponding function
button. The messages in the
display show you which function
is currently being displayed.
W'hile the function is displayed,
you can change it with the SET
knob. You can chanee anv
------ . _ - ----^ ^ .
programmed function at any time.
Ibnes
End-of-Cycle Tone (3 long beeps—
one second on, one second off):
shows that a timed oven operation
has reached STOP TIME or that
the Minute/Second Timer has ^
counted down.
Attention Tone (series of short
beeps, 1/4-second on, 1/4-second
off, until proper response is given):
will sound if oven has only been
partially programmed. For example,.
if you have selected a cook time but
1 iiu win ii&ai uic^ .
Attention Tone until you select a
temperature or push CANCEL.
Notification Tone (single, one-
cernnd hpf^.nV inrHratPQ avp . ti hnc
"--------- •------------------------ -
Stabilized at selected temperature,
r^cy luiic (a.mgic, i/iu-sccuiiu
beep): sounds when any button is
pushed.
11