FRIGIDAIRE FPID2495QF - Manual

(O
(D
CO
0)
00
0
00
■ ■
1
00
Service Mode Wiring Diagram
n (0
È
0)
s -s
fi,I
O CO 1
T3 — CO
111
■ s i ?
= 2,1
-1 i’c
fi »1
c c n
(0 M *5
d i
! § ! *
& a 3 D
® ” X 'w
c S- & c
® I
0) u 9i »
S-E:cj{
3 ® a *-
« 5 2 0
« « P ^
£ 8 5 O
8.11s
5 c S t
5 8^S
I"
>»*-
3 E
. e £T5
1. «
o 0>£
-« C (/)
1 5 *
til
III
3 « £
a S 0
j. e 0)
O (0 (0
c -a 3
After Cancel, press pad Heavy and Fast simultaneously for
at least 4 seconds to access Service Mode.
LED Heavy, Led Normal and Led Fast blink to Indicate
that Service mode is accesed.
After accessed Service mode ( Led Heavy, Led Normal and
Led Fast blinking):
1. Press pad Heavy to show the first alarm code.
- Led Heavy blinks to Indicate the machine Is In Alarm
Reading.
- The first alarm code saved is shown in the display. For
descriptions of alarm codes, please see Alarm Codes
section.
2. Press pad Heavy again to show the second alarm code.
3. Press pad Heavy once more to show the third alarm
code.
4. Press pad Heavy the fourth time to move to Actuator Test.
Press pad repeatedly will sequentially turn on one
actuator at a time.
- Led Heavy Is turned off. led Normal blincks to Indicate the
machine Is In Actuator Test.
- The actuator number Is shown In the display, see the follo­
wing table for details.
LED Test/Delete Alarm Memory
After accessed Service mode ( Led Heavy, Led Normal and
Led Fast blinking):
1. Press pad Normal to start this function.
-All LEDS and display blinks 5 seconds on 1 second off.
- Buzzer beeps 5 seconds and then off.
- The alarm codes saved In memory are erased.
2. The mode can be exit by pressing the CANCEL button,
or waiting 60 seconds after last button pressing.
Functional Test cycle
After accessed Service mode (Led Heavy, Led Normal and
Led Fast blinking):
1. Press pad Fast to start the test cycle.The cycle will not
start if door is opened.
- LED Normal blinks all the way through the whole cycle,
even If after the cycle Is finished
-The test cycle runs as a normal wash cycle.
It can be cancelled or run to its end.
Number of
pad Heavy
pressed Actuator
Number
in display Actuator
4 4 Regeneration Valve
5 5 Drain Pump
6 6 Inlet Valve
7 7 Heater
8 8 Wash pump
g 9 Dispenser
10 10 Dry Fan
5. Press pad Heavy when actuator number 10 Is activated,
the machine will cycle back to Alarm reading and show
the first alarm code saved.
6. The mode can be exit by pressing the CANCEL button,
or waiting 60 seconds after last button pressing.
W i r e - c o l o r
Code Color
bk black
br brown
bu blue
rd red
gn/ye green/yeliow
L i n e - s t y l e
= Component is
currently not in use
(reserved)
= Component is
optional
C o n n e c t i o n s i n c l u d e d i n W i r e H a r n e s s e s
WireHarness Connection WireEnd 01 WireEnd 02 WireEnd 03 WireEnd04 WireEnd 05
A 02 BaseBoard DrainPump WashPump
A 03 BaseBoard LeakageSwitch
A 04 BaseBoard FiowControl
A 05 BaseBoard InletValve
A 06 BaseBoard WashPumpTacho
A 07 BaseBoard BOF
A 08 BaseBoard PressureSensor NTC/Turb Sensor
A 09 BaseBoard Interface I
B 01 Interface I Userinterface
B 02 Userinterface Dispenser RinseAid
B 03 Userinterface Door lock
c 01 BaseBoard Heater
Cycle Selection Options
I 701 751 801 851 901 951 TOO! T051 TTOl ml T201 mi T301 mi T401 mi Ì501 T551 T601 Ì8
I ■ ■ ■ ■ I ■ ■ I ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I I ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ ■ I ■ ■ ■ I