Occurrence possible cause solution, Washer, Operating – FRIGIDAIRE Washer/Dryer User Manual
Page 14: Washer - water
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
WASHER
-
OPERATING
(ocntiraied)
Washar does not start
(cxxitirued).
CVcleselectcr isrot mcncxectpcsiticn.
More indicator clockwise sli^tly. Pullautkndc.
№tor is ovErh^ted.
WdsOnernictorwillstcpif itteoerresoverheated. Itvn.ll
autamticallyrestart after a cool down period of ip to
30minutes (if washer has not been rranually turned
c±0.
WiuberwKà't spin.
Lid is ret carpletelyclceed.
Close lidooTpletely.
Rasidus left intiib.
WASHER - WATER
Heavily goileditatis.
Wipe
tubwithancnabrasivehousdiold
cleanser,
than
rinse. Shake or brush excess dirt and sand from iteris
before washing.
Wash load too wet after
Washer is overloaded.
Do not overload washer. See Waahliig Procedures,
lead is out of balance.
Rearrange loadtoallcwproper ^Innirg'.
Etainhose is kinked.
Strai^taidrainhcse.
Water does not enter
washer or It ente» slowly.
Water sufply is not adegjate in area.
Check another faucet in the house. Wait unti 1 water
supply ardpressure increase.
Water supply faucets are not cotpletely qpai.
Fully open hot and cold faucets.
Water is being used elseitere in the house.
Wdterpressuremjstbeatleast30psi
(260kEa)
.Avoid
rurrdrgwaterelsaiierewhilewasiher is filling.
Water inlet hoses are kinked.
Straightanheses.
water level does not cover
Iced.
iTipKpervater level selecticn (for
niD^lsmthViaterlevel/lcadsizecmtrol).
Select hiфervвtнrlevel/lcad size.
Washer is overloaded.
Do not overload washer. Whan control is set at hiфest
fill
level,
drylстdleveldюuldnotbehiфerthantcp
row of circular holes In wash tub.
Warm or hot water is not
hot enou^.
Hbt water heater is set too low or is a
distance f ran laundry emter.
lyteasure hot water tereperature at nearby faucet viith
candy or meat thermometer. Water taiperature should
beat least 130°F (70°C) . Adjust water heater as
mces^ry.
Hbt water is being used elsevfere in
the house.
Avoid using hot water elsewhere before or during
washer use. There may not be enough hot water
availablefarprpercleanirg.
Ifprcblanpersists,
your
hot water system tray be unable to support more than
1 use at a tine.
Water In washer does not
drainer drains slowly.
Dralnhose is kinked or clogged.
Clean and straighten the drain hose.
water leaks.
Fill hose comectiaiat faucet or washer.
Check and tighten hose connections. Install rubber
seal ingwasihers provided.
House drainpipes are closed.
Uiclcg drainpipes. ContactpliiTber if necessary.
Cwersudsirg.
Use less detergent.
Incorrect wash and rinse
tenperatures.
Hbt and cold water hoses are connected
to wra::^ supply faucets.
Connect hot water hose to hot water faucet and cold
water hose to cold water faucet.
Water Is entering washer
but tub does not fill.
Ecainhffie stan:%)ipe is incorrect hei^it.
Standpipe must be a minimum of 33 " (83.82 cm) high,
to prevent siphoning. See INSTALLATION
INSTRUCTIONS.
1 4