Kenmore 625.3882 - Manual (Page 10)

f J J J J ,i J J J J J ,i J J
IJ..IJ J J J J. .1J J J J J J
SECTION 2 ,i J ,j J J J ,i J J J J J ,i J J
JJ J J J J J J J J J
J J . J J J J J J , J J J J J J J
HOW YOUR WATER SOFTENER WORKS
ij.jjjjjj.jjjjjj.jjjj
IJJJJJJJJJJJJJJJJJ
IJJJ^J^JJJJJJJJJJ rjjJjjÆjjjjj^jjjjj
ijjjj^majjjjjjjjjj
J JJJ^J J J
IJJJJJJJJJJJJJJJJJ rjJJJJJ^JJJJJJ^JJJJJ
IJJJJJJJJJJJJJJJJJ
^ EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam­
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera­
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
^ RECHARGE NOW
M l( h
I’UO
RECHARGE
Press the ON/OFF-HOLD but­
ton and hold
until ^RECHARGE,
Serv and Fill begin to flash in the display. Upon
reaching fill, the first cycle of regeneration, the flash­
ing Serv
goes off and Fill is on steady. RECHARGE
continues to flash. This regeneration will last for
about 2 hours. After the 2 hours, you will have soft
water again.
“^Note:
If the CLEAN feature is set to ON, a cleaning back­
wash {CLEAN
and Bkzvsh or Rinse flashes in the dis­
play, along with the minutes of the dean cycle re­
maining) precedes the recharge.
^ RECHARGE TONIGHT
~i,nn
MIJO
RECHARGE TONtGHl
WATER FLOW
Press and release (do not hold) the
ON / OFF-HOLD button. RE­
CHARGE TONIGHT
flashes in the display, and the
softener begins regeneration at the next preset re­
charge time. Press and release the ON/ OFF-HOLD
button once more if you dedde to cancel the regen­
eration, and RECHARGE TONIGHT.
^ SALT MONITOR SYSTEM
The face plate timer has a low salt monitor with an
indicator light to remind you to refill the storage
tank with salt. To set this monitor system:
Lift the salt hole cover and level the salt in the
storage tank.
The salt level decal, on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing be­
low). Observe the number the leveled salt is at
or closest to.
Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num­
ber. For example, the pictures below show the
salt level at 6.
Finally, set the level you want the low salt indi­
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (^) shows opposite this
number. In the example below, the light will
come on when the stored salt drops to level 2. At
level 2, the storage tank is about 1 / 3 full. This is
the lowest you should allow the stored salt level
to drop to (see note on page 1-6).
If you wish to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
For accurate salt monitor operation, always use
nugget or pellet water softener salt. See page 1-6.
2 - 1