Kenmore Washer - Manual (Page 15)

Auto Temp Control
АТС {Auto Temp Control) electronically senses and maintains a
uniform water temperature. АТС regulates incoming hot and cold
water. The АТС is automatically turned On when a cycle is
selected. (See "Preset Cycle Settings” in “Cycles.”)
АТС is available with WARM/WARM, WARM/COLD and COLD/
COLD settings. The AUTO TEMP CONTROL light will glow
indicating that АТС is working.
_ A uto T emp
CONTHOL
• HOT/COLO
• WARM/WARM
• W arm / C old
• COLD/COLD
• TAP COLD/COLD
W ash /R inse
TEMP
■ АТС ensures consistent cleaning.
■ When using АТС, warm water is added to the washer to
maintain a termperature of approximately 75°F (24°C), so
detergents dissolve properly.
■ Warm washes are regulated at approximately 100°F (38°C).
■ Warm rinses are regulated at approximately 75“F (24°C). This
is a cooler warm rinse than you are used to, but it saves
energy and gives proper rinsing. The load is a comfortable
temperature to remove from the washer
Wash Time
Wash Time is preset for each wash cycle, (See “Preset Cycle
Settings” in “Cycles.”) As you press WASH TIME pad, the cycle
time (minutes) will increase or decrease in the ESTIMATED TIME
REMAINING display and a different WASH TIME light will glow. To
get the minimum wash time, press the pad until the indicator light
next to MINIMUM illuminates. This is the shortest wash time
available for that cycle.
•
• M aximum
4. Press SET DELAY TIME. 1H (one hour) will be displayed in the
time display window. The indicator light for DELAY TIME will
glow.
5.
6 .
. Di lAr TIMF'
УЧ
SETttLAY
TIME
For a longer delay time, press SET DELAY TIME. The time will
increase by one^hour steps.
Press START. The countdown to the wash cycle will show in
the time display window.
To change the Delay Time:
■ Press STOP/CANCEL.
■ Reset the SET DELAY TIME.
■ Press START to begin the countdown.
To cancel Delay Start:
Press START again to begin the cycle right away or press
STOP/CANCEL twice.
Adjustable End Of Cycle Signal
A tone will sound at the end of the cycle. The sound level of this
tone can be adjusted by pressing END OF CYCLE SIGNAL. The
volume of tone you will hear at the end of the cycle will sound as
the pads are pressed.
• HIGH
• Low
• OFF
E nd of C ycle
SIGNAL
* NORMAL
»
»M inimum
W ash T ime
When a wash cycle is started, the estimated time remaining for
the cycle, including fills and drains, will be displayed. The time
will count down to the end of the cycle. The ESTIMATED TIME
REMAINING light will glow.
> EbTiMAIKli TiNCi
RtVlAINlj'JG
О
Set Delay Time
You can use the SET DELAY TIME feature to delay the start of a
wash cycle for up to 11 hours (depending on you model).
1, Load the washer and fill the dispensers.
2, Close the washer lid.
3, Select the desired Cycle, Options and Modifiers.
Indicator Lights
Select Cycle
Located next to each pad, these lights show the cycle you have
selected.
Options
These lights show the Prewash and/or Rinse/Spin Options you
have selected.
Modifiers
These lights show the selected Wash/Rinse Temperature, Wash
Time, Estimated Time Remaining in cycle, and End of Cycle
Signal.
Washer Status
These lights show what portion of the cycle the washer is
operating.
W ashfr S tatus
• W'ASHiNl.i
• R insing
• A uk ,’ Fluff
• C k / ihls C ifan
15