Pioneer CT-W505R - Manual (Page 10)

FRONT PANEL FACILITIES
TWO MODES COUNTER
Counter Mode button (TIME/COUNT)
Press the button, and 2 nnodes change alternately.
Tape counter zz Time counter
■ Tape counter
Different counters are provided for DECK 1 and 11. The number on
the counters increase/decrease as a tape runs. It is useful if you
make a note of the location and length of a selection while re­
cording or playing back. You can then easily locate a desired se­
lection or where to resume recording.
■ Time counter
• This indicates the elapsed time for recording or playback. This
automatically starts counting when recording or playback starts.
During fast-forwarding/rewinding, the counter automatically
switches to a tape counter.
• The time counter indicates only the time duration of recording or
playback. When recording or playback is changed to fastforward­
ing, rewinding, or music search, the counter switches from the
time counter to the tape counter. When the operation returns to
recording or playback, the counter switches to the time counter.
• Tape counter indication
/ / 1 111 11
u IJ IJ IJ
Time counter indication
n n. n n
u u. IJ IJ
Counter reset button (RESET)
Press this button to reset the tape counter to 0 D D 0, or to reset the
time counter to u 0:0 0.
Counter indicator during music search
Nomral tape counter indicator
Counter indicator during music search
n n n n
u u u u
O 1 n I
( |f u /
Plus sign
0 - n I
1 I U I
Minus sign
• A plus sign (-I-) appears during music search in the forward di­
rection.
• A minus sign (-) appears during music search in the reverse
direction.
The last two digits of the counter indicator show the number of
selections to be skipped. If three selections are to be skipped, for
example, it shows "P+03" initially. The number then decreases
by 1 each time a selection is skipped ("P+02" = "P+01 etc.).
When the deck resumes playback, the normal tape counter reap­
pears.
PLAYBACK
StNGLE PLAYBACK (Either DECK I or DECK II) BLANK SKIP
1. Load a prerecorded tape in DECK I or II.
2. Set the DOLBY NR switch.
• Always set the switch to the same position that was used for
recording,
3. Set the REV MODE switch (see page 8).
4. Set the stereo amplifier for tape playback.
5. Press the playback (► or -4) button of either DECK I or
II.
To improve high frequency sound during playback in
tapes with poor recordings
Press the FLEX button and playback the tape.
To stop playback temporarily (DECK II only)
Press the pause (II) button.
• To resume playback, either press the pause (II) button again, or
press the playback (► or ◄) button.
To stop playback
Press the stop (■) button.
10
<RRB1170>
En
This function allows you to skip unrecorded portions of the tape
during playback.
Set the REV MODE switch to czo .
NOTE:
• When the REV MODE switch is set to the czd position, the relay
mode will be selected.
• When this mode is selected, if the tape deck encounters an unre­
corded portion of tape more than 15 seconds in length, it will fast
forward the tape until it encounters another recorded portion, and
resume playback from that point.
RELAY PLAYBACK
When relay playback mode is selected, continuous playback can be
performed. When the tape in the first deck reaches its end and
stops, the other deck will automatically begin playback.
1. Load prerecorded tapes in DECK I and DECK II.
2. Set the DOLBY NR switch.
• Always set the switch to the same positions that were used
for recording.
3. Set the REV MODE switch to
czd
(see page 11).
4. Set the stereo amplifier for tape playback.
5. Press the playback (► or
- 4 )
button of the deck that
will start to play first.
• When the tape in one deck ends, the other deck automatically
begins playback.
• To cancel relay playback, press the stop (■) button.