Using the recorder, Il restarting playback from the beginning, Continuing from where you left off – KORG Concert Korg Digital Piano C-150 User Manual
Page 16: Whaf the [start/stop] lamp means, Playback, Recording, Playing back
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Using the Recorder
1. Recording
Press a [VOICE SELECTOR] to select a voice.
E.PtANO
HARPS!
VIBES
ORGAN
STRINGS
' U"
IQ
](
□
Q
Press the [RECORD] switch.
The lamp on the [RECORD] switch comes on, and
recording standby.
The RECORD lamp comes on,
START/STOP RECORD
IT
CIE
--------- RECORDER
To begin recording, do any of the following: (a)
press [START/STOP] switch, (b) strike a note on
the keyboard, or (c) press down on a pedal.
START/STOP RECORD
The START/STOP lamp comes on
if you begin by pressing [START/STOP]switch, the
piano counts out a two-bar lead-in before starting
actual recording. If you being by pressing a pedal
or key, recording starts immediately.
While recording is in progress, the [START/STOP]
lamp remains on.
Note; The piano records any voice changes that you make
while recording is in progress. Note, however, that
the piano does not store the initial voice used for
the recording {the voice you selected at Step 1
above). Before playing the recording back, you
should select this voice manually.
To stop recording, press the [START/STOP]
switch.
To pause at the present position, press the [START/
STOP] switch briefly. The recording pauses and the
[START/STOP] lamp begins to blink.
To return the recorder to its start position, hold the
[START/STOP] switch for longer than one second.
The recorder returns and the [START/STOP] lamp
goes out.
START/STOP
Ti—n
Press the switch briefly
the recorder pauses at its
current position, and the
[START/STOP] lamp
begins btinking.
START/STOP
Hold the switch down:
the recorder returns to
its start position, and the
(START/STOP) lamp
goes out.
Note: the piano can record data for one song. If you begin
recording again from the beginning, the new data
will overwrite the existing data.
il Restarting playback from the beginning
To stop the replay and start over from the beginning,
depress [START/STOP] switch for longer than one
second to return the recorder to its start position. Then
repeat the recording procedure starting from step 1
bn the previous page.
■ Continuing from where you left off
if you paused the recorder (as described in step 4
above), you can resume by pressing the [RECORD]
switch and then the [START/STOP] switch. If you re
turned the recorder to its start position, play back
your recording to its end, press [RECORD] switch,
then [START/STOP] switch.
Note: Any voice changes made in the newly recorded ma
terial will be ignored when the material is played
back. The voice selection made in the original or first
recording of the song will be in effect for playback
of the entire song, including the appended material.
Note: Using the [START/STOP] switch to stop in the
middle of playback and switch to recording will
sometimes cause the newly recorded material to
begin at a slightly different place from where play
back was stopped.
Note; When cueing a track for re-recording, the data for
the remainder of the track will be lost. The remain
der of the track, to the end, must be re-recorded.
Whaf the [START/STOP] lamp means...
Lamp is ON
Recording or playback is in
progress.
Lamp is BUNKING Recorder is paused at the middle
or end of a recording.
Lamp is OFF
Recording is at the start position.
2. Playing Back
■ Playback
Check the recorder position
START/STOP
n—tr
Hold the switch down: the
recorder returns to its start
position, and the [START/STOP]
lamp goes out.
b
If the [START/STOP] lamp is blinking, the recorder
is paused at the middle or end off the recording. If
you want to start playback from the beginning, hold
down the [START/STOP] switch for at least one sec
ond (until the lamp goes out).
1 6