Comtrol MC5001 - Manual (Page 2)

PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001
Industrial Media Converter
co nnec t. c o mmunicat
e . c o ntrol. PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001
Industrial Media Converter
co nnec t. c o mmunicat
e . c o ntr o l.
PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001
Industrial Media Converter
co nnec t. c o mmunicat
e . c o ntr
o l. PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001
Industrial Media Converter
co nnec t. c o mmunicat
e . c o ntr o l.
PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001 Industrial Media Converter
co nnec t. c o mmunicat
e . c o ntr
o l. PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001
Industrial Media Converter
connec
t. c o mmunicat
e . c o ntr o l.
PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001
Industrial Media Converter
co nnec t. c o mmunicat
e . c o ntr o l. PWR TX RX Ring
RX
TX
ROCKET
LINX
MC5001
Industrial Media Converter
co nnec t. c o mmunicat
e . c o ntrol.
Note: The recommended working voltage is 24VDC (12-48VDC) or 24VAC (12-32VAC)
with polarity reverse protection. The RocketLinx MC5001 is a serial to fiber media converter with an RS-232/422/485 port with
auto sensing baud rate and direction control functions. It extends the distance of serial
communication to 5KM (MC5001, Multi-Mode) or 40KM (MC5001, Single-Mode) and also
provides good immunity for EMI/EMC. The RocketLinx MC5001 supports 15KV ESD
protection on the serial line. It also features a wide power input range
(12-48VDC/12-32VAC) and DIN rail mounting for quick and easy installation.
Package Checklist
 MC5001 Industrial serial to fiber media converter
 Quick installation guide
 DIN rail mount kit
Mounting the RocketLinx MC5001
DIN Rail mount: screw on the DIN rail mounting clips
with the four screws and mount MC5001 on the DIN Rail.
Grounding the RocketLinx MC5001
There is one earth grounding pole included on the
power input connector. Connect the earth ground of the
MC5001 to ensure system safety and to prevent noise.
Wiring the Power Inputs
1. Insert the positive and negative wires into the
V+ and V- contacts on the terminal block connector.
2. Tighten the wire-clamp screws to prevent the
power wires from being loosened.
Introduction
V+ V- GND
Accepts 24AWG wire.
The MC5001 provides triple mode circuits for RS-232/422/485 2/4-wires and extends these
signals to 5KM or 40KM by optical fiber cable. The converter operating architecture can also
be configured as a PTP (Peer to Peer) or SFR (Serial Fiber Ring) to enlarge the serial
communication infrastructure and link additional MC5001s.
To ensure the quality of the serial line signal, the MC5001 provides two termination resistors
for the RS-422/485 TX and RX signal by using the DIP switch enable/disable option. Refer to
the DIP switch setting table for more information.
The following diagram illustrates different serial connectivity options:
Connecting to serial line
DTR
DSR
RTS
CTS
GND
TX
RX
DTR
DSR
RTS
CTS
RX
TX
GND
TX
RX
GND
GND
RX
TX
PC with RS-232 serial RS-232 serial mode RS-232 serial mode Device with RS-232 serial
MC5001 MC5001
RX
TX
TX
RX
Fiber
GND
Data-
Data+
DTR
DSR
RTS
CTS
RX
TX
GND
TX
RX
GND
GND
Data-
Data+
MC5001 MC5001
RX
TX
TX
RX
Fiber
PC with RS-232 serial Device with 2-wires
RS-485 serial RS-485/2 wires serial mode RS-232 serial mode
RX+
RX-
TX+
TX-
GND
TX+
TX-
RX+
RX-
GND
GND
RX-
RX+
TX-
TX+
GND
TX-
TX+
RX-
RX+
PC with 4-wires
RS-422/485 RS-422/485 4-wires
serial mode RS-422/485 4-wires
serial mode Device with 4-wires
RS-422/485 serial
MC5001 MC5001
RX
TX
TX
RX
Fiber
GND
Data-
Data+ GND
Data-
Data+ Data+
Data-
GND Data+
Data-
GND
MC5001 MC5001
RX
TX
TX
RX
Fiber
PC with 2-wires RS-485 RS-485 serial mode RS-485/2 wires serial mode Device with 2-wires
RS-485 serial
The Fiber Optical link architecture supports PTP
and SFR mode for different purposes.
PTP Mode (Peer to Peer)
The PTP (Peer to Peer) mode provides connection
between 2 nodes. When working in this mode, the
MC5001 can transmit and receive data at the same
time, which means the MC5001 is working at
full-duplex mode.
Connecting the Optical Fiber
SFR Mode (Serial Fiber Ring)
To extend the transmission distance and to
save fiber cable cost, the MC5001s can link to
each other in a ring architecture. In this mode
the MC5001 only provides half-duplex
transmission and all data communication is
controlled by the host device. The maximum
number of communication nodes is 20.
SFR Mode
Half Duplex
RS-232 RS-232 RS-232 RS-485
Optical Fiber
The table below illustrates fiber transceiver specifications.
TxPwr(Min):Minimum Launch Power TxPwr(Max):Maximum Launch Power
RxPwr(Min):Maximum Receive Sensitivity RxPwr(Max):Minimum Receive Sensitivity
Link Budget=Minimum Launch Power –Maximum Receive Sensitivity
Note: To ensure fiber converter transmission/reception of data between nodes, the
attenuation of the optical fiber cable should not exceed the fiber converter’s Link
Budget.
40km
5km
Fiber
Cable (um) Connecter Wavelength(um) TXPwr
(Min)
TxPwr
(Max)
RxPwr
(Min)
RxPwr
(Max) LinkBudg(dBm) Distance(km)
Single-mode
8~10/125 ST 1310nm -9dBm -8dBm -27dBm N/A 18dBm
Model
MC5001
Single Mode
MC5001
Multi Mode
Multi-mode
50~62.5/125 ST 820nm -12dBm -9dBm -28dBm N/A 16dBm
Earth Ground
PWR
TX
RX
Ring
RX TX
ROCKET LINX MC5001 Industrial Media Converter connect. communicate. control.
RS-232/422/485 RS232
PTP Mode
RocketLinx MC5001
1 2 3 4