Crosman P4 - Manual

Stinger P4
6mm BB Spring Powered Pistol
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN
Crosman Corporation
7629 Routes 5 & 20
Bloomfield, NY 14469
www.crosman.com
1-800-724-7486 MODEL: P4-515
If you have any questions regarding your airsoft gun, please contact Crosman at 1-800-724-7486, 585-657-6161 or www.crosman.com.
READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE USING THIS AIRSOFT GUN. AND REMEMBER, THIS AIRSOFT GUN IS NOT A TOY. TREAT IT WITH THE SAME RESPECT YOU WOULD
A FIREARM.
THIS IS NOT A TOY. ADULT SUPERVISION REQUIRED. MISUSE OR CARELESS USE MAY CAUSE SERIOUS INJURY, ESPECIALLY TO THE
EYE. EYE PROTECTION MUST BE USED BY THE USER AND ANY PERSON WITHIN RANGE. MAY BE DANGEROUS UP TO 100 YARDS (91.44 METERS). READ
OWNER’S MANUAL BEFORE USING.
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR SHOOTING GLASSES TO PROTECT YOUR EYES.
READ ALL INSTRUCTIONS BEFORE USING.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND OWNERSHIP OF THIS AIRSOFT GUN.
DO NOT BRANDISH OR DISPLAY THIS AIRSOFT GUN IN PUBLIC – IT MAY CONFUSE PEOPLE AND MAY BE A CRIME. POLICE AND
OTHERS MAY THINk IT IS A FIREARM. DO NOT CHANGE THE COLORATION AND MARkINGS TO MAkE IT LOOk MORE LIkE A FIREARM. THAT IS DANGEROUS
AND MAY BE A CRIME.
THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS kNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH
DEFECTS (OR OTHER REPRODUCTIVE HARM).
1. Safety First
• ALWAYS treat the AIRSOFT GUN as though it is loaded and ready to fire.
• ALWAYS treat AIRSOFT GUNs with the same respect you would a firearm.
• ALWAYS store the AIRSOFT GUN unloaded.
• ALWAYS store the AIRSOFT GUN away from children.
• ALWAYS aim in a SAFE DIRECTION.
• ALWAYS keep the muzzle of the AIRSOFT GUN pointed in a SAFE DIRECTION.
• ALWAYS keep your finger off the trigger and out of the trigger guard until ready to shoot.
• ALWAYS keep the AIRSOFT GUN “ON SAFE” until you are ready to shoot (see section 3A).
• ALWAYS check to see if the AIRSOFT GUN is “ON SAFE” (see section 3A) and unloaded when receiving it from another person.
• ALWAYS have you and others wear shooting glasses to protect your eyes.
• ALWAYS wear shooting glasses over eye glasses if your prescription or reading glasses are not safety glasses.
• ALWAYS place the backstop in a location that will be safe should the backstop fail.
• ALWAYS check your backstop for wear before and after each use. All backstops are subject to wear and will eventually fail. Replace your backstop if
the surface is worn or damaged, or if a ricochet occurs.
• ALWAYS use the proper size BB in your AIRSOFT GUN. Check the markings on your AIRSOFT GUN to verify the BB size is 6mm.
• NEVER reuse ammunition.
• NEVER shoot at hard surfaces or at the surface of water. The BB may bounce off or ricochet and hit someone or something you had not intended
to hit.
• NEVER attempt to disassemble or tamper with your AIRSOFT GUN. Use an Authorized Service Station.
• Modifying the function of your AIRSOFT GUN in any way, may be unsafe and will void your warranty.
• NEVER point the AIRSOFT GUN at any person or at anything you do not intend to shoot.
2. learning the parts of your new airsoft gun
Learning the names of the parts of your AIRSOFT GUN will help you understand your owner’s manual.
A. Rear Sight
B. Barrel
C. Front Sight
D. Muzzle
E. Trigger
F. Trigger Guard
G. Grip
H. Safety (Cylinder Release) (Fig. 2)
I. Slide
J. Magazine
K. Magazine Release Button
3. Operate the Safety
NEVER point the AIRSOFT GUN at anything you do not intend to shoot.
A. Put the AIRSOFT GUN “ON SAFE”
1. Ensure the AIRSOFT GUN is pointing in a SAFE DIRECTION.
2. Locate the Safety (H) on the left side of the AIRSOFT GUN.
3. Rotate the safety downward (Fig. 2) until the lever fully stops.
B. Take the AIRSOFT GUN “OFF SAFE”
1. Rotate the Safety (H) upward for “OFF SAFE”.
2. When the AIRSOFT GUN is “OFF SAFE” it can be fired.
4. Cocking Your Airsoft Pistol
1. Put the AIRSOFT GUN “ON SAFE” (see Section 3A).
2. Point the airsoft pistol in a SAFE DIRECTION.
3. While holding the airsoft pistol in a horizontal position, cock by firmly holding the slide with your
entire hand, pulling the slide rearward in a smooth motion (Fig. 3) and then releasing.
4. Your AIRSOFT GUN is now ready to fire and must be cocked before each shot.
5. Load and Unload Airsoft BBs
A. Loading the Airsoft GUN
1. Make sure the AIRSOFT GUN is “ON SAFE” (Section 3A) and pointed in a SAFE DIRECTION.
2. While supporting the BB magazine, push the Magazine Release Button and remove the magazine.
3. Pull and hold down the BB follower tab (fig. 4)
4. Insert up to 14 plastic BBs into the BB loading hole on the front and top of the magazine (fig 4).
5. Place a finger over the end of the magazine where the BBs will exit.
6. With the magazine pointed in a safe direction, release the BB Follower Tab.
NOTE: Releasing the BB follower tab quickly, or without the end covered, could allow BBS to exit the magazine.
7. Insert the loaded clip into the airsoft gun
8. Your airsoft gun is now loaded and ready to fire, after reading the entire manual.
CAUTION: Use .6mm BBs ONLY. NEVER REUSE BBs. USE OF ANY OTHER AMMUNITION CAN CAUSE INJURY TO YOU OR
DAMAGE TO THE AIRSOFT GUN.
B. Unloading The Airsoft Gun
1. Make sure the AIRSOFT GUN is “ON SAFE” (Section 3A) and pointed in a SAFE DIRECTION.
2. While supporting the BB magazine, push the Magazine Release Button and remove the magazine.
3. Pull down the BB retainer button and lock in place
4. Tip the magazine upside down. Remove each BB by slowly and gently pushing the BB toward the opening with your finger tip.
6. Aim and Fire Safely
1. You and others with you should ALWAYS wear eye protection designed for airsoft to protect your eyes.
2. Always aim your AIRSOFT GUN in a SAFE DIRECTION.
3. Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit someone or something you had not
intended to hit.
4. DO NOT re-use plastic BBs because they could possibly cause damage to your AIRSOFT GUN.
5. Your AIRSOFT GUN is designed for target shooting and is suited for both indoor and outdoor use. Always remember to place your target carefully.
6. THINk about what you will hit if you miss the target.
7. Your AIRSOFT GUN is correctly aimed when the front sight blade is position exactly in the notch of the rear sight.
8. The top of the front sight blade should be even with the top of the notch in the rear sight. The bulls-eye should appear to rest on the top of the
front sight (Fig. 5).
9. When you are sure of your target and backstop, and the area around the target is clear:
a. Take the AIRSOFT GUN “OFF SAFE” (section 2A)
b. Aim
c. Pull the trigger to fire
7. Maintain Your Airsoft gun
1. Put one (1) drop of Crosman 0241 Pellgunoil ® on the tip of every CO
2
cylinder in order to properly maintain your AIRSOFT GUN.
2. DO NOT use petroleum distillate based oil or solvent and DO NOT over-oil as this can cause damage to your AIRSOFT GUN.
3. DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the AIRSOFT GUN in any way inconsistent with
this manual may make your AIRSOFT GUN unsafe to use, cause serious injury, especially to the eye, and will void
the warranty.
4. If you drop your AIRSOFT GUN, visually check to see that it works properly before you use it again.
5. If anything seems changed, like a shorter or weaker trigger pull, this may mean worn out or broken parts. Call Crosman
customer service for assistance before using your AIRSOFT GUN again.
6. To clean the AIRSOFT GUN barrel
a. Spray a cleaning patch with Crosman Nitro Lubricant oil
b. With the cleaning patch on the rod, insert it into the barrel to clean
c. Swab the barrel 3-4 times
d. Repeat the swabbing procedure with a dry patch
e. The barrel is clean when the patches come out clean after dry swabbing
8. Clearing a Jam
1. Make sure the AIRSOFT GUN is “ON SAFE” and pointed in a SAFE DIRECTION
2. With the gun pointed in a safe direction, push the Magazine Release Button and remove the magazine.
3. If there is a BB in the barrel, use a cleaning rod (not included) to remove the BB by inserting the tapered end of the cleaning rod into the muzzle and CAREFULLY and
slowly applying pressure until the BB exits the barrel.
IMPORTANT: Never use sharp metal tools to remove BBs from the gun.
SPECIFICATIONS
Mechanism BB Repeater Power Source Spring
Sights Front Fixed Blade Velocity Up to 325 fps
Sights Rear Fixed Notch Length 9.5 inches
Caliber/Ammunition 6 mm Plastic BB Safety Trigger Block
Capacity Up to 14 BBs Weight 6.2 oz.
PERFORMANCE
Your AIRSOFT GUN was designed to function best with Crosman ® branded ammunition. Using other than Crosman branded ammunition may cause your product to malfunction and may
void your warranty. For optimum performance use Crosman ammunition only.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our customer service representatives are here to help you. Contact us directly at 1-800-7AIRGUN (1-800-724-7486). You can also get answers to frequently asked questions at
www.crosman.com.
CUSTOMER SERVICE
If your AIRSOFT GUN is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800- 724-7486 or 585-657-6161. (International customers should
contact their distributor.) DO NOT ATTEMPT TO DISASSEMBLE IT! Crosman assumes no warranty responsibility if the gun has been disassembled.
LIMITED 30 DAY WARRANTY
This product is warranted to the retail consumer for 30 days from date of retail purchase against defects in material and workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform normal maintenance. Any other expense. CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, OR INCIDENTAL EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
HOW TO OBTAIN WARRANTY PERFORMANCE
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to product. Package and return to Crosman Corporation, Routes 5 & 20,
Bloomfield, NY 14469.
International Customers: Please return product to your nearest distributor. If you do not know your distributor, please call 585-657-6161 and ask for our International Department
for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF
RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be preempted, it shall not be applicable. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
CROSMAN, DUTY CALLS, and GAME FACE are registered trademarks of Crosman Corporation in the United States.