Crosman CP01 - Manual

Model CP01
6mm BB CO
2
Airsoft BB Repeater
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN
Marine Corps trademarks used under license by Crosman Corporation.
Crosman Corporation
7629 Routes 5 & 20
Bloomfield, NY 14469
www.crosman.com
1-800-724-7486
Made in the U.S.A. with some foreign components. MCCP01A515
WARNING: This is not a toy. Adult supervision is required. Misuse may cause serious
injury, especially to the eye. Eye protection designed for airsoft guns must be worn by the
user and any person in range. May be dangerous up to 100 yds. Read the owner’s manual
before using.
WARNING:
Do not brandish or display this airsoft gun in public – it may confuse
people and may be a crime. Police and others may think it is a firearm. Do not change the
coloration and markings to make it look more like a firearm. That is dangerous and may be
a crime. READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING
THIS AIRSOFT GUN.
WARNING:
This product contains a chemical known to the state of California to cause
cancer and birth defects (and other reproductive harm).
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR EYE PROTECTION TO PROTECT YOUR EYES.
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE AND OWNERSHIP OF
THIS AIRSOFT GUN.
RECOMMEND 18 YEARS OR OLDER TO PURCHASE. INTENDED FOR USE BY THOSE 16 OR OLDER.
Please read this owner’s manual completely. And remember, this airsoft gun is not a toy. Treat it with the same re-
spect you would a firearm. Always carefully follow the safety instructions found in this owner’s manual and keep this
manual in a safe place for future use.
If you have any questions regarding your new airsoft gun, please contact Crosman at 1-800-724-7486,
585-657-6161 or www.crosman.com.
1. Learning the Parts of Your New Airsoft gun
Learning the names of the parts of your new airsoft gun will help you to understand your owner’s manual. Use this
manual to increase your enjoyment of this airsoft gun.
A
B
C
D E
F
G
H
Fig 1
A. Muzzle
B. Front Sight
C. Safety (fig. 2)
D. Barrel
E. Rear Sight
F. Grip
G. Piercing knob (fig. 3)
H. Magazine Release Button
I. Trigger
J. Trigger Guard
2. Operating the Safety
A. To Put the Airsoft Gun “ON SAFE:”
• Locate the safety on the right side of the airsoft gun.
• Push the safety in and all the way forward toward the “S” for “ON SAFE” (Fig. 2).
The safety is not “ON SAFE” unless it is pushed all the way forward and the red
around the safety is NOT showing.
Like all mechanical devices, an airsoft gun safety can fail. Even when the safety is “ON
SAFE”, you should continue to handle the airsoft gun safely.
NEVER point the airsoft gun at any person. NEVER point the airsoft gun at anything
you do not intend to shoot.
B. To Take the Airsoft gun “OFF SAFE”:
• Push the safety in and all the way backward toward the “F” for “OFF SAFE”.
When you can see the RED ring around the left side of the safety, the airgun is”OFF SAFE” and can be fired.
3. Installing and Removing the CO
2
Cartridge
A. Installing a New CO
2
Cartridge
WARNING: CO
2
cartridges may explode at temperatures above 120°F (48.9°C). Do not
mutilate or incinerate them. Do not expose them to heat or store CO
2
cartridges at tempera-
tures above 120°F (48.9°C).
• Put the airsoft gun “ON SAFE” (see Section 2A).
• Make sure the airsoft gun is UNLOADED and POINTED IN A SAFE DIRECTION.
• Holding the airsoft gun as shown, slide the grip straight back and remove (Fig. 3).
• Turn the piercing knob left until it is all the way down.
• Insert the new CO
2
cartridge into the airsoft gun with the small neck of the CO
2
cartridge
inserted first and up.
• Finger-tighten the piercing knob by turning it right. If you hear a hissing sound when
piercing the gun, try tightening the screw more.
• Line the grip up with the groove on the frame and slide the grip forward to close.
• To make sure the cartridge has been pierced, point the airsoft gun in a SAFE DIRECTION,
take “OFF SAFE” (see Step 2B) and pull the trigger.
• If the airsoft gun does not make a popping noise after pulling the trigger, the CO
2
is not
being discharged. In that event put the airsoft gun “ON SAFE” (Step 2A), remove the grip
and tighten a 1/4 turn. Replace the grip.
• Point the airsoft gun in a SAFE DIRECTION, take “OFF SAFE” (see Step 2B) and pull the
trigger.
NOTE: We recommend the use of Crosman ® Powerlet ® CO
2
cartridges. They are made to
fit your airsoft gun. Other brands of CO
2
cartridges may not fit properly and if you force them
into place it may result in injury to you or damage to your airsoft gun. Never try to force any
CO
2
cartridge into or out of place.
Do not store your airsoft gun with a CO
2
cartridge in it. If you know you will not be using your airsoft gun for an
extended period of time, empty the CO
2
cartridge and remove it from the airsoft gun (Step 3B).
This is very important to remember, as it will prolong the longevity of your airsoft gun seals.
B. Removing CO
2
Cartridge
WARNING: Keep hands away from escaping CO
2
gas. It can cause frostbite if allowed
to come in contact with skin. Always make sure the CO
2
cartridge is empty before attempt-
ing to remove it from the airsoft gun by slowly turning the knob counter-clockwise all the way
until you no longer hear the escape of CO
2
gas.
• Put the airsoft gun “ON SAFE” (section 2A).
• Make sure the airsoft gun is UNLOADED (section 4B) and pointed in a SAFE DIRECTION.
• Use one hand to hold the airsoft gun at the top of the receiver, being sure not to cover the muzzle.
• Loosen the cartridge piercing knob by slowly turning it left (see fig. 3) allowing any remaining gas to escape.
• Drop out the CO
2
cartridge.
• Tighten the cartridge piercing knob enough so that the grip will pass over it.
• Line the grip up with the groove on the frame and slide the grip forward to close.
4. Loading and Unloading Plastic BBs
A. Loading Plastic BBs
• Make sure the airsoft gun is “ON SAFE” (See Step 2A) and pointed in a SAFE DIRECTION.
• Remove the magazine by pressing on the magazine release button on the left
side of the airsoft gun.
• Pull and hold down the BB follower tab (fig. 4)
• Insert up to 15 plastic BBs into the BB loading hole on the front of the magazine.
• Place a finger over the end of the magazine where the BBs will exit.
• With the magazine pointed in a safe direction, release the BB Follower tab.
NOTE: Releasing the BB follower tab quickly, or without the end covered, could al-
low BBS to exit the magazine.
• Insert the loaded clip into the airsoft gun
• Your airsoft gun is now loaded and ready to fire, after reading the entire manual,
including section 7 on reviewing safety.
B. Unloading Plastic BBs
• Put the airsoft gun “ON SAFE” (See Step 2A).
• Point the airsoft gun in a SAFE DIRECTION.
• Remove the magazine by pressing on the magazine release button.
• Pull and hold down the BB follower tab.
• Tip the magazine until all the plastic BBs fall out of the hole.
• If a BB is still visible in the top of the magazine, push the BB out of the magazine.
• Aim the airsoft gun in a SAFE DIRECTION; insert the magazine into gun, take it “OFF SAFE” (See Step 2B) and fire.
Fig. 2
F S
“On Safe”
Fig 3
Piercing Lever
• Repeat this procedure several times until you are sure you are no longer firing BBs.
NOTE: The airsoft gun must be charged with CO
2
when following these steps but remember, do not store your
airsoft gun with a CO
2
cartridge in it.
WARNING:
Even though you go through the unloading procedure, continue to treat the
airsoft gun as though it were loaded. Do not point at anything you do not intend to shoot.
5. Aiming and Firing Safely
• You and others with you should always wear eye protection designed for airsoft
to protect your eyes.
• Always point your airsoft gun in a SAFE DIRECTION.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may
bounce off or ricochet and hit someone or something you had not intended to hit.
• DO NOT re-use plastic BBs because they could possibly cause damage to your
airsoft gun.
• Your airsoft gun is designed for target shooting and is suited for both indoor and
outdoor use. Always remember to place your target carefully. THINK about what
you will hit if you miss the target.
• Your airsoft gun is correctly aimed when the front sight blade is positioned
exactly in the notch of the rear sight. The top of the front sight blade should be even with the top of the notch in
the rear sight. The bulls-eye should appear to rest on the top of the front sight (Fig. 5).
• When you are sure of your target and backstop, and the area around the target is clear, take the airsoft gun
“OFF SAFE” (section 2A) aim and pull the trigger to fire.
6. Maintaining Your Airsoft gun
• Putting 1 drop of Crosman 0241 Pellgunoil ® on the tip of every CO
2
cylinder will help to maintain your airsoft
gun. DO NOT use petroleum distillate based oil or solvent and DO NOT over-oil as this can cause damage to
your airsoft gun.
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft gun in any way inconsistent
with this manual may make your airsoft gun unsafe to use, cause serious injury, especially to the eye and will
void the warranty.
• If you drop your airsoft gun, visually check to see that it works properly before you use it again.
• If anything seems changed, like a shorter or weaker trigger pull, this may mean worn out or broken parts. Call
Crosman customer service for assistance before using your airsoft gun again.
A. How to clean the magazine
• Remove magazine
• Wipe down outside of magazine
• Spray small amount of Crosman Nitro Lubricant oil into BB tube
• Replace magazine
B. To clean the Airsoft gun barrel
• Spray a cleaning patch with Crosman Nitro Lubricant oil.
• With patch on rod, insert in into barrel to clean
• Swab barrel 3-4 times
• Repeat swabbing procedure with a dry patch
• Barrel is clean when patches come out clean after dry swabbing.
C. Clearing a Jam
Never look down the end of barrel to see if a jam has been cleared.
• Make sure the airsoft gun is “ON SAFE” and pointed in a SAFE DIRECTION.
• Remove magazine.
• Insert the tapered end of the cleaning rod into the barrel.
• CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
• Reinstall the magazine and test gun.
7. Reviewing Safety
• Do not ever point the airsoft gun at any person. Do not ever point the airsoft gun at anything you do not intend
to shoot.
• Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm.
• Always aim in a SAFE DIRECTION. Always keep the muzzle of the airsoft gun pointed in A SAFE DIRECTION.
• Always keep the airsoft gun “ON SAFE” until you are ready to shoot in a SAFE DIRECTION.
• Always check to see if the airsoft gun is “ON SAFE” and unloaded when getting it from another person or from
storage.
• Always keep your finger off the trigger and out of the trigger guard until ready to shoot.
• You and others with you should always wear eye protection to protect your eyes.
• Always wear eye protection designed for airsoft over your regular glasses.
• Use 6 mm plastic BBs only.
• Do not reuse plastic BBs because they could cause possible damage to your airsoft gun.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit
someone or something you had not intended to hit.
• Replace the backstop if it becomes worn. Place the backstop in a location that will be safe should the backstop fail.
• Your backstop should be checked for wear before and after each use. All backstops are subject to wear and will
eventually fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.
• Do not attempt to disassemble or tamper with your airsoft gun.
• DO NOT MODIFY OR ALTER YOUR AIRSOFTGUN. Attempts to modify the airsoft gun in any way may make
your airsoft gun unsafe to use, cause serious injury or death and will void the warranty.
• Using unauthorized repair centers or modifying the function of your airsoft gun in any way may be unsafe and
will void your warranty.
• Do not put the airsoft gun away loaded. Make sure ALL of the plastic BBs are unloaded from the airsoft gun.
• Always store this airsoft gun in a secure location.
SPECIFICATIONS
Mechanism BB Repeater Sights
Front: Fixed Blade
Rear: Fixed Notch
Caliber/Ammunition 6 mm Plastic BB Capacity Up to 16 BB
Power Source 12 gram CO
2
cartridge Velocity Up to 400 fps
Length 7.1 inches Safety Slide
Weight 1.1 lbs
PERFORMANCE: Many factors can affect velocity, including brand of projectile, type of projectile and barrel condi-
tion.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our customer service representatives will help. You can get answers to frequently asked
questions at www.crosman.com or you can contact us directly at 1-800-7AIRGUN (1-800-724-7486)
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800-
724-7486 or 585-657-6161. (International customers should contact their distributor.) DO NOT ATTEMPT TO
DISASSEMBLE IT! If you take it apart you probably will not be able to reassemble it correctly. Crosman assumes no
warranty responsibility under such circumstances.
For optimum performance use Crosman ammunition only. Using other than Crosman branded ammunition may
cause your product to malfunction and may void your warranty.
LIMITED 30 DAY WARRANTY
This product is warranted to the retail consumer for 30 days from date of retail purchase against defects in material
and workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform nor-
mal maintenance. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, OR INCIDENTAL
EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to
product. Package and return to Crosman Corporation, Routes 5 & 20, East Bloomfield, NY 14443.
International Customers: Please return product to your nearest distributor. If you do not know your distributor,
please call 585-657-6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF RETAIL PURCHASE.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be pre-
empted, it shall not be applicable. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.
Check out our complete line of Marine Corps airsoft products at marinesairsoft.com
For more information about the Marine Corps and becoming a Marine, visit marines.com
Officially Licensed Product of the United States Marine Corps, www.marines.com and 1.800.marines.