Futaba 2NCS - Manual (Page 8)

Your NEW FUTABA Digital Proportional R/C Sys-
tern is guaranteed against defects in workmanship
and material for 180 days from the date of purchase
when the attached registration card is returned to
us within ten days of purchase.
This Guarantee is null and void if the R/C system
has been improperly handled, damaged in a crash, or
tampered with and does not cover the replacement
of plastic housings or electronic components
damaged due to the use of improper voltages.
When service is required, please take your equip-
ment to your local authorized service station or ship
it directly to us. All postage, shipping, and insurance
charges must be paid by the user.
•When requesting repair of trouble that has oc-
curred suddenly of from long use, describe the
trouble symptoms in as much detail as possible.
This will facilitate detection of the trouble point
and shorten the repair period greatly.
•Defects caused by faulty materials or workmanship
will be corrected free of charge.
•This limited warranty is null and void if the set has
been tampered with or disassembled.
Refer to warranty statement for details.
•WHEN VEHICLE WILL NOT BE USED
Be sure and release the connector of running
Nicd battery except when you are on the way
to the starting line.
When not using the
connector, set the
switch to OFF.
Release the connector.
To obtain the best possible range (car to transmitter
distance) and reduce the possibility of interference,
please observe these antenna routing instructions.
Failure to follow these guidelines can result in loss
of control or limited range
1) NEVER cut your receiver's antenna wire.
Your system has been precisely tuned to the full
length of the stock antenna.
2) Excess antenna wire should NOT be tightly
coiled. To safely store the excess wire make
an antenna shortener from a small piece of stiff
cardboard. This will provide maximum reception
and prevent tangling and breakage of the wire.
3) When routing the antenna wire to the antenna
tube keep the wire away from battery and speed
control wiring. The high power of the NiCd
battery creates electrical "noise" which can cause
interference.
SNOW IS WATER
Remember that operating your FX10 on snow
or in wet areas is not recommended. Melted
snow becomes water which will damage or short
out your system's electronics._____
FP-S148 •SPLINED HORNS
This horn permits shifting of the
servo neutral position at the servo
horn. Setting and shifting the neutral
position
1) The splined horn has 25 seg-
ments. The amount of change per
segment is; 360-25 !e 14.4°
2) The minimum adjustable angle is
determined by the number of arms or
number of the holes. For four arms,
the minimum adjustable angle is:
b) Effect
To shift the holes center line to the
right (clockwise) relative to baseline
A, shift arm 2 to the position of arm
1 and set it to the position closet to
baseline A.
angular shift per segment is 14.4°.
The shift to the right is 90° - (14.4 x
6) = 3.6°
To shift by the same angle in the
opposite direction, use the opposite
arm number.
For a six arm horn, turn the arm
counterclockwise and set arm 2 to
the position of arm 1. The adjustable
angle is 60° - (14.4 x 4) =2.4°.
Arm 3 shift 4.8° to the right, arm 6
shifts 2.4° to the left, and aim 4
shifts 7.2° to the right and left
No. Part name
1. Upper case
2. M i d d l e case
3. Bottom case
4. Metal bearing
5. Metal bearing
6. Potentiometer
8. Motor
9. Motor pinion
10. Screw
11. 1st gear
12. 2nd gear
13. 3rd gear
14. Final gear
15. Intermediate shaft
16. 2nd s h a f t
17. Servo horn A
18. Binding head tapping screw 2.6 x8
19. Printed w i r i n g board S148
20. S148 3PB-WRB300G
21. w g u m bush
22. Pan head truss screw
23. Nameplate S148
Part No.
FCS-48
FCS-48
FCS-48
S04137
S04136
I 39668
S91259
802461
J50002
FOS-48
FGS-48
FGS-48
FGS-48
S02495
S02494
FSH-6X
FSH-4I
AS1157
AT2453
S90045
S50360
S60099
FUTABA CORPORATION OF AMERICA
4 Studebaker, Irvine California 92718, I .S.A.
Phone:714-455-9888 Telex: 23-0691227 Facsimile: 714-455-9899
FUTABA (EUROPE) GmbH
Am Seestern 24, D-4000, Dusseldorf 11, W. Germany.
Phone:021 1-5287-0 Faesimile:0211-593133
FUTABA CORPORATION
Tokyo Office: INAGAKI BLDG., 3F 1-21-3, Kanda sudacho, Chiyoda-ku, Tokyo, Japan.
Phone: (03)255-681 1 Facsimile: (03)255-6880