Programming thermostat schedules – Carrier 33CS User Manual
Page 3
correct time is shown, press the Mode/Next button to modify
the day of the week. The current day will blink on and off.
Press the UP ARROW and DOWN ARROW buttons until
the correct day is shown. Press the Set Clock button again
to exit the Set Time mode.
Programming Thermostat Schedules —
Be-
fore programming the thermostat, plan the thermostat daily
schedule. The schedule is divided into 7 days (Monday through
Sunday). Each day can have 2 (Occupied 1, Unoccupied),
3 (Occupied 1, Occupied 2, Unoccupied), or 4 (Occupied 1,
Occupied 2, Occupied 3, Unoccupied) time periods. Each
occupied time period has a start time, stop time, heating set
point and a cooling set point. The unoccupied time period
has a heating set point and a cooling set point. The unoc-
cupied time period is active whenever an occupied time
period is not active. Fill in Table 1 below as an aid to pro-
gramming the daily schedules.
PROGRAMMING MODE — To program the daily sched-
ules, perform the following procedure:
1. Enter programming mode by pressing the Program but-
ton. The Occupied 1 annunciator will appear on the ther-
mostat display. See Fig. 5. Use the UP ARROW and
DOWN ARROW buttons to set the maximum number
of Occupied periods available. The thermostat can be
set to 1, 2, or 3. After the number of Occupied periods
has been selected, press the Mode button.
2. The cooling set point for Occupied 1 will be displayed.
Use the UP ARROW and DOWN ARROW buttons
to raise or lower the cooling set point until the desired
temperature is shown. The range of acceptable values is
35 to 99 F (1 to 37 C). Press the Mode button to con-
tinue. See Fig. 5.
3. The heating set point for Occupied 1 will be displayed.
Use the UP ARROW and DOWN ARROW buttons to
raise or lower the heating set point until the desired tem-
perature is shown. The range of acceptable values is
35 to 99 F (1 to 37 C). Press the Mode button to con-
tinue. See Fig. 5.
4. The cooling set point for Unoccupied will be displayed.
Use the UP ARROW and DOWN ARROW buttons to
raise or lower the cooling set point until the desired tem-
perature is shown. The range of acceptable values is
35 to 99 F (1 to 37 C) or ‘‘OF’’(no unoccupied cooling).
Press the Mode button to continue.
5. The heating set point for Unoccupied will be displayed.
Use the UP ARROW and DOWN ARROW buttons to
raise or lower the heating set point until the desired tem-
perature is shown. The range of acceptable values is
35 to 99 F (1 to 37 C) or ‘‘OF’’ (no unoccupied heating).
Press the Mode button to continue.
6. The day of the week will be shown. Use the UP AR-
ROW and DOWN ARROW buttons to change the day
of the week until the desired starting day is shown. Pos-
sible choices are M (Monday) through S (Sunday). Press
the Mode button when the desired day is shown.
7. The Start Time for Occupied 1 will be displayed. Use
the UP ARROW and DOWN ARROW buttons to raise
or lower the time until the desired Start Time is shown.
Press the Mode button to continue. See Fig. 6.
Table 1 — Daily Schedule Planner
DAY
OF THE
WEEK
SCHEDULE
Occupied 1
Occupied 2
Occupied 3
Unoccupied
Start / Stop / Heat / Cool
Start / Stop / Heat / Cool
Start / Stop / Heat / Cool
Heat / Cool
Monday
/
/
/
/
/
/
/
/
/
/
Tuesday
/
/
/
/
/
/
/
/
/
/
Wednesday
/
/
/
/
/
/
/
/
/
/
Thursday
/
/
/
/
/
/
/
/
/
/
Friday
/
/
/
/
/
/
/
/
/
/
Saturday
/
/
/
/
/
/
/
/
/
/
Sunday
/
/
/
/
/
/
/
/
/
/
NOTE: The cooling temperature set point must be higher than the heating temperature set point.
Fig. 4 — Setting the Clock
Fig. 5 — Setting Occupied 1 Set Points
3