Clarion DXZ845MC - Manual (Page 24)

24
DXZ845MC
English
Operations Common to Each Mode
Setting the clock
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [ a] or [d] button to select
“CLOCK ”.
3. Press the [ ] button.
4. Press the [ a] or [d] button to select the
hour or the minute.
5. Turning the [ROTARY] knob clockwise or
counterclockwise to set the correct time.
› The clock is displayed in 12-hour format.
6. Press the [ ] button to store the time into
memory.
7. Press the [T] button to return to the previous
mode.
Note:
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the
car’s battery or take out this unit, the clock is re-
set. While setting the clock, if another button or
operation is selected, the clock set mode is can-
celed.
Turning the screen saver function
on or off
This unit is provided with the screen saver func-
tion which allows you to show various kinds of
patterns and characters in the Operation Status
indication area of the display. You can turn on
and off this function.
If the button operation is performed with the
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
› The factory default setting is “ON”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [ a] or [d] button to select
“SCRN SVR ”.
3. Press the [ ] button.
4. Turning the [ROTARY] knob clockwise or
counterclockwise to select the setting. Each
time you turning the [ROTARY] knob, the set-
ting changes in the following order:
OFF
➜ ON ➜ MESSAGE
5. Press the [T] button to return to the previous
mode.
Entering MESSAGE INFORMATION
When the use of the message is selected for the
screen saver setting, you can change the con-
tents of the message.
› Up to 30 characters can be entered.
› The factory default setting is “Welcome to Clarion”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [ a] or [d] button to select
“MSG INPUT ”.
3. Press the [ ] button.
4. Press the [ a] or [d] button to move the
cursor.
5. Press the [D] button to select a character.
Each time you press the [D] button, the char-
acter changes in the following orders:
Capital letters
➜ Small letters ➜ Numbers
and Symbols
➜ Umlaut ➜ Capital letters…
6. Turning the [ROTARY] knob to select the de-
sired character.
7. Repeat step 4 to 6 to enter up to 30 charac-
ters for message.
8. Press and hold the [ ] button for 2 sec-
onds or longer to store the message in
memory and cancel input message mode.
› Press the [BND] button can cancel the input
message. Then press and hold the [ ] but-
ton for 2 seconds or longer to store the mes-
sage and the message return to default set-
ting.
9. Press the [T] button to return to the previous
mode.
Message display
When the unit is powered on or off, a message
is displayed. The user can turn this message
display ON or OFF.
› The factory default setting is “ON”.
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [ a] or [d] button to select
“MESSAGE”.
3. Turning the [ROTARY] knob clockwise or
counterclockwise to set the message display
“ON” or “OFF”.
4. Press the [T] button to return to the previous
mode.