Golden Lighting 5050-6 CH - Manual

Assembly Instructions: 5050-3/6 CH (Danica)
IMPORTANT:
• All InstAllAtIon work shoulD be Done by AccreDIteD professIonAl.
• shut off power supply At fuse or cIrcuIt breAker!
• use only the specIfIeD bulbs. Do not exceeD the mAxImum wAttAge!
PRePARINg fOR INsTAllATION
carefully remove all of the contents from the carton. see the
important notes above. shut off the power at the circuit breaker
and completely remove the old fixture from the wall, including
the old mounting strap.
Mounting strap (B) contains several pairs of threaded holes. Find
the pair of holes that matches the spacing of the holes on the
junction box and your fixture backplate. Two of mounting screws
(A) should be attached to mounting strap (B). You may need to
tighten nuts (C) that hold these screws in place. Pull the house
wires through the center of mounting strap (B). Place mounting
strap (B) over the junction box so that mounting screws (A) are
vertical, and in alignment with the hole locations on canopy (F).
Secure mounting strap (B) to the junction box with mounting
screws (D) and a screwdriver. Tighten the screws securely.
AsseMblINg THe fIxTuRe
To begin, remove cable lock (U) from fixture base (X) by twisting
the wire off. remove shade holders (V) and rotate the lamp
shade holders 180 degrees so that they are pointing outwards
and the lamp shade fits into the base. Secure shade holders
(V) into place by threading on cable lock (U). Place the base of
the fixture on a flat surface. Gently slide candle sleeves (S) over
sockets (t). place lamp shade (r) into position on shade holders
(V). Adjust the shade until it is centered and level.
By measuring, determine the correct number of rods needed for
proper hanging height. There are 3,12” rods (J) and 1, 6” rod (K)
included with the fixture. To shorten the fixture, trim the wires
to the desired length plus at least 8 to 10 inches. You must at
least use one of rods (K). Put the wire through the rods and pull
until taut. Thread the bottom rod onto the threads of fixture body
(L). Adjust cable wires (Q) so that the fixture will be level when
installed. Hang the decorative chain by connecting the rings.
Join the top rod to swivel connection (H) of canopy (F).
CONNeCTINg THe WIRes
Have an assistant support the fixture weight while completing
the wiring. Cut away excess wire. Thread the fixture wires
through canopy (F). Attach the fixture’s wires to the power
supply wires from the junction box. Connect black to black (or
smooth); white to white (or ribbed); ground to ground (green or
copper). Twist the ends of the wire pairs together, then twist on
a wire connector. make sure all twists are in the same direction.
If there is no ground wire (green or copper) from the junction
box, locate ground screw (E) on mounting strap (B) and wrap
the fixture ground wire around the green ground screw (E). Use
a screwdriver to secure ground screw (E) onto the mounting
bracket. Tuck all wires neatly into the junction box.
fINIsHINg THe INsTAllATION
Push canopy (F) up to the ceiling so that mounting screws (A)
protrude through the holes in canopy (F). Secure the canopy
to the ceiling by tightly threading decorative nuts (G) onto the
screws.
Install the light bulbs (not included) in accordance with
the fixture’s specifications. Do not exceed the maximum
recommended wattage.
your installation is now complete. turn on the power and test
the fixture.
CleANINg TIPs
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
for Customer service, contact
the place of purchase to arrange
for replacement parts.
A
D
G
F
H
J
B
C
I
K
L
M
N
O
P
R Q
S
U
T
V
W
X
E