Great Planes Shoestring GP/EP ARF - GPMA1328 - Manual (Page 4)

4
Propeller
If you are installing a glow engine, choose a prop based
on the engine manufacturer’s recommendation. If you are
installing the recommended RimFire brushless motor, we
suggest an APC 11x5.5E propeller (APCQ1055).
Batteries and Charger
For a brushless motor installation, two 3350mAh 11.1V
Lithium Polymer battery packs connected in series are
recommended. Order numbers for the battery packs and
series connector are provided below:
❏
Great Planes LiPo 3350mAh 11.1V 25C Discharge
w/Balance (GPMP0541)
❏
Great Planes Series Deans ® U 2 to 1 Adapter
(GPMM3143)
A cell balancer is required for the LiPo battery listed above:
❏
Great Planes ElectriFly ™ Equinox ™ LiPo Cell
Balancer 1-5 (GPMM3160)
A suitable charger is also required. The Great Planes
PolyCharge4
™ is designed for LiPo packs only, but is able
to charge four LiPo packs simultaneously. The Great Planes
Triton2
™ charger will only charge one pack at a time, but is
capable of charging NiCd, NiMH, LiPo, and Pb acid batteries.
Order numbers for both are provided below:
❏
Great Planes PolyCharge4 DC Only 4 Output LiPo
Charger (GPMM3015)
OR
❏
Great Planes ElectriFly Triton2 DC Comp Peak Charger
(GPMM3153)
ADDITIONAL ITEMS REQUIRED
Required Hardware and Accessories
This is the list of hardware and accessories required to fi nish
the Shoestring .46 ARF. Order numbers are provided in
parentheses:
❏
R/C foam rubber (1/4" [6mm] - HCAQ1000, or
1/2" [13mm] - HCAQ1050)
❏
3' [900mm] standard silicone fuel tubing (GPMQ4131)
(glow engine only)
Adhesives and Building Supplies
This is the list of Adhesives and Building Supplies that are
required to fi nish the Shoestring .46 ARF:
❏
1/2 oz. [15g] Thin Pro ™ CA (GPMR6001)
❏
1/2 oz. [15g] Thick Pro CA– (GPMR6013)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Threadlocker thread locking cement (GPMR6060)
❏
Denatured alcohol (for epoxy clean up)
❏
Drill bits: 1/16" [1.6mm], 5/64" [2mm], 3/32" [2.4mm],
3/16" [4.8mm], 1/4" [6.4mm]
❏
Great Planes Tap & Drill Set 6-32 (GPMR8102) (Glow
engine installation only)
❏
Tap handle (GPMR8120) (Glow engine installation only)
❏
Rotary tool with cutting bit
❏
#1 Hobby knife (HCAR0105)
❏
#11 blades (XACR3111)
❏
Medium T-pins (100, HCAR5150)
❏
Top Flite ® MonoKote ® sealing iron (TOPR2100)
❏
Top Flite Hot Sock ™ iron cover (TOPR2175)
❏
220 grit sandpaper
❏
Panel Line Pen (TOPQ2510)
Optional Supplies and Tools
Here is a list of optional tools that will help you build the
Shoestring .46 ARF:
❏
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❏
2 oz. [57g] spray CA activator (GPMR6035)
❏
4 oz. [113g] aerosol CA activator (GPMR6034)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Pro 6-minute epoxy (GPMR6045)
❏
Epoxy brushes 6, (GPMR8060)
❏
Mixing sticks (GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Pliers with wire cutter (HCAR0630)
❏
Harry Higley's 3/16" Extended Drill (HIGR1020)
❏
Rotary tool reinforced cut-off wheel (GPMR8200)
❏
Servo horn drill (HCAR0698)
❏
Hobby Heat ™ micro torch II (HCAR0755)
❏
Dead Center ™ Engine Mount Hole Locator
(GPMR8130)
❏
Precision Magnetic Prop Balancer (TOPQ5700)
❏
AccuThrow ™ Defl ection Gauge (GPMR2405)
❏
CG Machine ™ (GPMR2400)
❏
Hobbico Flexible 18" Ruler Stainless Steel (HCAR0460)
❏
Top Flite MonoKote trim seal iron (TOPR2200)
❏
Top Flite MonoKote heat gun (TOPR2000)
❏
Hobbico Pin Vise 1/16 Collet w/6 Bits (HCAR0696)