CatEye CC-CD300DW [Double Wireless] - Manual (Page 2)

MODE
MODE MODE MODE MODE MODE MODE MODE MODE
MODE MODE
MENU MENU
MODE MODE MODE
Pace arrow
Indicates whether the current speed
is faster ( ) or slower (
) than the
average speed.
Operating the computer [Measuring screen]
Tm
Elapsed Time
0:00’00” - 9:59’59”
Dst Trip Distance
0.00 - 999.99 km [mile]
Dst 2
Trip Distance-2
0.00 - 999.99 /
1000.0 - 9999.9 km [mile]
Av
Average Speed *2
0.0 - 105.9 km/h
[0.0 - 65.9 mph]
Mx Maximum Speed
0.0(4.0) - 105.9 km/h
[0.0(3.0) - 65.9 mph]
Odo Total Distance
0.0 - 9999.9 /
10000 - 99999 km [mile]
Clock
0:00 - 23:59
or 1:00 - 12:59
*1 With the computer installed on the bracket, press
on the three raised dots on the face of the
computer.
*2 If Tm exceeds approximately 27 hours or DST
exceeds 999.99 km, .E (Error) is displayed as
the average speed. Reset data.
Current speed
0.0(4.0) - 105.9 km
[0.0(3.0) - 65.9 mph]
Changing the computer settings [menu screen]
If the MENU is pressed with the measuring screen displayed, the menu screen
appears. Press the MODE when measurement has stopped and no signal is
being received to change menu settings.
Starting/Stopping measurement
Measurements occur automatically when
the bicycle is in use. During
measurement,
or flashes.
Switching computer function
Pressing MODE switches function, in
order, as shown on the left.
Resetting data
To reset measurement data, display any
data other than for Dst-2 and then press and
hold MODE. Pressing and holding MODE
with Dst-2 displayed resets Dst-2 only.
The total distance is never reset.
Power-saving function
If the computer has not received a signal
for 10 minutes, power-saving mode will
activate and only the clock will be
displayed. When the computer receives a
sensor signal again, the measuring screen
reappears. If two weeks’ inactivity elapses,
power-saving mode will change to SLEEP
mode. Pressing the MODE in SLEEP mode
brings up the measuring screen.
Selected Mode
*1
Wheel selection ..... Toggle between the specified wheel size (tire circumference)
and . Use this function if the computer is to be shared
between two bicycles.
................................ Pressing MODE toggles between and .
Wheel size entry .... Pressing MODE increases the value, and pressing and
holding MODE moves to the next digit.
* To enter the wheel size
, display using “Wheel selection”.
Clock setting .......... To set the clock, refer to “Preparing the computer-4”.
Total distance manual entry
................................ Before reinitializing the computer, note the total distance. This
reading will later allow you to enter the total distance
manually. Pressing MODE increases the value, and pressing
and holding MODE moves to the next digit.
Speed unit .............. Pressing MODE toggles between and .
Maintenance
To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and
wipe it off with a dry cloth.
Replacing the battery
Computer
If the display appears faded, replace the battery.
Install a new lithium battery (CR2032) with the (+)
side facing upward. Then reinitialize the computer
referring to “Preparing the computer”.
* When the battery is installed, place the seal with
the “TOP” side upward.
Sensor
If sensor reception is poor, replace the battery.
After replacement, check the positions of the sensor and magnet.
Setting
change (by
pressing &
holding)
Wheel
selection
Wheel size
entry
Clock setting Total distance
manual entry
Speed unit
* After changing, be sure to press MENU to register the
setting.
* If the menu screen is not touched for a minute, the
Measuring screen reappears without data changes.
TOP
TO P
CR2032
Seal
COIN
Push!
LIMITED WARRANTY
2-Year Computer only
(Accessories/Bracket sensor and Battery Consumption excluded)
CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years
from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no
charge. Service must be performed by CatEye or an authorized retailer.
To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for
repair. Please write or type your name and address clearly on the warranty certificate.
Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.
For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory
rights.
CO.,LTD.
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn: CATEYE Customer Service Section
Service & Research Address for USA
CATEYE Service and Research Center
1705 14th St. 115 Boulder, CO 80302
Phone:
303.443.4595
Toll Free: 800.5CATEYE
Fax:
303.473.0006
E-mail: [email protected]
URL: http://www.cateye.com
#160-2190
Parts kit #160-2196
Speed sensor
#160-0280
Bracket band
#169-9691
Wheel magnet
Standard Parts
CR2032
Troubleshooting
MODE does not work when the computer is mounted on its bracket.
Check that there is no dirt between the bracket and the computer.
Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly.
The sensor signal reception icon does not flash. (The speed is not displayed.)
(Spin the front wheel, bringing the computer closer to the sensor. If the icon now flashes, this indicates that the
computer and sensor are too far apart or that the battery is low.)
Is the clearance between the sensor and magnet too great? (must be ≤ 5 mm)
Does the magnet pass through the sensor zone?
Adjust the positions of the magnet and sensor.
Is the computer installed at the correct angle?
Back of computer must face toward the sensor.
Are the computer and sensor too far apart? (The distance must not exceed 70 cm.)
Install the sensor closer to the computer.
Is the computer or sensor battery weak?
In winter, battery performance diminishes.
Replace the battery. In the case of the computer, after replacing the battery, re-start the computer according to the
“Preparing the computer”, above.
No display.
Is battery in the computer run down?
Replace it. Then reinitialize the computer referring to “Preparing the computer”.
Incorrect data appear.
Reinitialize the computer referring to “Preparing the computer”.
Specification
Battery ................. Computer : Lithium battery (CR2032) x 1
Sensor : Lithium battery (CR2032) x 1
Battery life ........... Computer : Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary
depending on the conditions of use.)
Sensor : Unit Total Distance reaches about 10,000 km (6,250 mile)
* This is the average figure of being used under 20 °C temperature and the distance between the computer and the
sensor is 65 cm.
Controller .................................. 4-bite, 1-chip microcomputer (Crystal controlled oscillator)
Display ...................................... Liquid crystal display
Sensor ...................................... No contact magnetic sensor
Wheel circumference range ..... 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm)
Working temperature ............... 32
°F - 104 °F (0 °C - 40 °C) (This product will not function appropriately when exceeding the
Working Temperature range. Slow response or black LCD at lower or higher temperature
may happen respectively.)
Dimensions/weight ................... 1-53/64” x 1-7/32” x 5/8” (46.5 x 31 x 16 mm) / 0.78 oz (22 g)
* The factory-loaded battery life might be shorter than the above-mentioned specification.
* The specifications and design are subject to change without notice.
#166-5150
Lithium battery
(CR2032)
#160-2193
Bracket
CC-RD300W