Cypress CY7C1336H - Manual

PRELIMINARY
2-Mbit (64K x 32) Flow-Through Sync SRAM
CY7C1336H
Cypress Semiconductor Corporation • 198 Champion Court • San Jose , CA 95134-1709 • 408-943-2600
Document #: 001-00210 Rev. *A Revised February 6, 2006
Features
• 64K x 32 common I/O
• 3.3V core power supply
• 3.3V I/O supply
• Fast clock-to-output times
— 6.5 ns (133-MHz version)
— 8.0 ns (100-MHz version)
• Provide high-performance 2-1-1-1 access rate
• User-selectable burst counter supporting Intel
®
Pentium
®
interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed write
• Asynchronous output enable
• Supports 3.3V I/O level
• Offered in JEDEC-standard lead-free 100-pin TQFP
package
• “ZZ” Sleep Mode option
Functional Description [1]
The CY7C1336H is a 64K x 32 synchronous cache RAM
designed to interface with high-speed microprocessors with
minimum glue logic. Maximum access delay from clock rise is
6.5 ns (133-MHz version). A 2-bit on-chip counter captures the
first address in a burst and increments the address automati-
cally for the rest of the burst access. All synchronous inputs
are gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CE
1
), depth-expansion Chip Enables (CE
2
and CE
3
), Burst
Control inputs (ADSC, ADSP, and ADV), Write Enables
(BW
[A:D]
, and BWE), and Global Write (GW). Asynchronous
inputs include the Output Enable (OE) and the ZZ pin.
The CY7C1336H allows either interleaved or linear burst
sequences, selected by the MODE input pin. A HIGH selects
an interleaved burst sequence, while a LOW selects a linear
burst sequence. Burst accesses can be initiated with the
Processor Address Strobe (ADSP) or the cache Controller
Address Strobe (ADSC) inputs. Address advancement is
controlled by the Address Advancement (ADV) input.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
The CY7C1336H operates from a +3.3V core power supply
while all outputs may operate with a +3.3V supply. All inputs
and outputs are JEDEC-standard JESD8-5-compatible.
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
ADDRESS
REGISTER
BURST
COUNTER
AND LOGIC
CLR
Q1
Q0
ENABLE
REGISTER
SENSE
AMPS
OUTPUT
BUFFERS
INPUT
REGISTERS
MEMORY
ARRAY
MODE
A [1:0]
ZZ
DQs
A0, A1, A
ADV
CLK
ADSP
ADSC
BW D
BW C
BW B
BW A
BWE
CE1
CE2
CE3
OE
GW
SLEEP
CONTROL
DQ A
BYTE
WRITE REGISTER
DQ B
BYTE
WRITE REGISTER
DQ C
BYTE
WRITE REGISTER
BYTE
WRITE REGISTER
DQ D
BYTE
WRITE REGISTER
DQ D
BYTE
WRITE REGISTER
DQ C
BYTE
WRITE REGISTER
DQ B
BYTE
WRITE REGISTER
DQ A
BYTE
WRITE REGISTER
Logic Block Diagram
[+] Feedback