G-Shock 5302 - Manual (Page 6)

E-40
To swap your Home Time and World Time Cities
1. In the World Time Mode, use
E to select the city you want to use as your new Home City.
2. To swap, press A and B at the same time.
$ and %
• This will make the World Time City you selected in step 1 (LON (LONDON)) your new Home City.
• Your previous Home City (TYO (TOKYO)) will be your new World Time City.
E-41
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use
D to select the Stopwatch Mode as shown on page E-8.
The mode dial hand will move to STW.
To perform an elapsed time operation
E E E E A
Start Stop (Restart) (Stop) Reset
To pause at a split time
E A A E A
Start Split
(SPL appears in
the upper display.) Split release Stop Reset
Hours
Seconds
Minutes 1/100
second
Hours
Seconds
Minutes 1/100
second
E-42
To measure two fi nishes
E A E A A
Start Split
First runner fi nishes.
(SPL appears in the
upper display.)
Display time of fi rst
runner Stop
Second runner
fi nishes. Split release
Display time of
second runner Reset
Note
• The Stopwatch Mode can indicate elapsed time up to 23 hours, 59 minutes, 59.99 seconds.
• Digital Meter A shows the 1/10 seconds count.
• Once started, stopwatch timing continues until you press E to stop it, even if you exit the Stopwatch
Mode to another mode and even if timing reaches the stopwatch limit defi ned above.
E-43
Using the Countdown Timer
The countdown timer can be confi gured to start at a preset time and sound an alarm when the end of the
countdown is reached.
To enter the Countdown Timer Mode
Use
D to select the Countdown Timer Mode as shown on page E-8.
• The mode dial hand will move to TMR and the lower display will show
the current countdown time.
To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the seconds counting
down), press E to stop it and then press A to reset to the current
countdown start time.
• If a countdown is paused, press A to reset to the current
countdown start time.
2. Hold down A until the minute setting of the current countdown start time starts to fl ash. This is the
setting screen.
3. Use E (+) and B (–) to change the minute.
• To set the starting value of the countdown time to 60 minutes, set 60'00.
4. Press A to exit the setting screen.
Countdown time
(Minutes, seconds) Countdown time
(Minutes, seconds)
E-44
To perform a countdown timer operation
E E E E A
Start Stop (Restart) (Stop) Reset
• Digital Meter A shows the seconds count.
• Before starting a countdown timer operation, check to make sure that a countdown operation is not
already in progress (indicated by the seconds counting down). If it is, press E to stop it and then A
to reset to the countdown start time.
• An alarm sounds for ten seconds when the end of the countdown is reached. This alarm will sound in
all modes. The countdown time is reset to its starting value automatically after the alarm sounds.
To stop the alarm
Press any button.
E-45
Using the Alarm
You can set fi ve independent daily alarms. When an alarm is turned on,
an alarm will sound for about 10 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. This is true even if the
watch is not in the Timekeeping Mode. One of the daily alarms is a
snooze alarm. The other four are one-time alarms. The snooze alarm will
sound every fi ve minutes up to seven times or until it is turned off.
You can also turn on an Hourly Time Signal, which will cause the watch
to beep twice every hour on the hour.
To enter the Alarm Mode
Use
D to select the Alarm Mode as shown on page E-8.
• The mode dial hand will move to ALM, the upper display will show the
currently selected alarm number (AL1 to AL4, or SNZ), or the hourly
time signal indicator (SIG).
• When you enter the Alarm Mode, the data you were viewing when you
last exited the mode appears fi rst.
Alarm number or SIG
Alarm time
(Hour : Minutes)
Alarm number or SIG
Alarm time
(Hour : Minutes)
E-46
To set an alarm time
1. In the Alarm Mode, use E to scroll through the alarm screens in the
upper display until the one you want to change is shown.
AL1 AL2 AL3
SIG SNZ AL4
2. Hold down A until the hour digits of the alarm setting start to fl ash in the lower display.
• This is the setting screen.
3. Press D to move the fl ashing between the hour and minute settings.
4. While a setting is fl ashing, use E (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no
indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
To test the alarm
In the Alarm Mode, hold down
E to sound the alarm.
Alarm ON/OFF
indicator Alarm ON/OFF
indicator
E-47
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use
E to select an alarm or the Hourly Time Signal.
2. When the alarm or the Hourly Time Signal you want is selected, press A to turn it on and off.
• The alarm on indicator (when any alarm is on), snooze alarm indicator
(when the snooze alarm is on), and the Hourly Time Signal on indicator
(when the Hourly Time Signal is on) are shown on the upper display in
all modes.
To stop the alarm
Press any button.
Hourly time signal
on indicator
Alarm on indicator
Snooze alarm indicator
Hourly time signal
on indicator
Alarm on indicator
Snooze alarm indicator
Operation Guide 5302