G-Shock 3266 - Manual (Page 2)

Operation Guide 3266
E-10
General Guide
• Press C to change from mode to mode.
• Holding down C for about one second in any mode switches directly to the Diving
Mode. Holding down C for about one second in the Diving Mode switches to the
Timekeeping Mode.
• In any mode (except when a setting screen is on the display),
press B to illuminate the display.
lllllllll ll
llllllll lll
Hold down C. ▲ ▲
Diving Mode
Timekeeping Mode
▲
Press C.
E-11
lll
lllllll lllll
llllllll
ll llllllll
lllll
llll l
▲
Log memory Recall Mode Tide/Moon Data Mode
Countdown Timer Mode Stopwatch Mode Alarm Mode
World Time Mode
▲
▲ ▲
▲ ▲
E-12
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• Press A to toggle between the day of the week and date (Date screen), and the
currently selected World Time city and time (Dual Time screen).
lllllllll ll
Date Screen
PM indicator Hour : Minutes Seconds
Day of week
Dual Time Screen
lllllllll ll
Dual time City code Month – Day
A
▲ ▲
E-13
Read This Before You Set the Time and Date!
This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the time, it is important that you first
select the correct city code for your Home City (the city where you normally use the
watch). If your location is not included in the preset city codes, select the preset city
code that is in the same time zone as your location.
• Note that all of the times for the World Time Mode city codes (page E-36) are
displayed in accordance with the time and date settings you configure in the
Timekeeping Mode.
To set the time and date manually
1. In the Timekeeping Mode hold down A until the city
code starts to flash, which indicates the setting screen.
2. Use D and B to select the city code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table” at the back of this manual.
l ll
lll
ll ll
ll
l l l l
E-14
Change the city code
Toggle between Daylight Saving Time ( ON )
and Standard Time ( OFF ).
Toggle between 12-hour ( ) and 24-
hour ( ) timekeeping
Use D (east) and B
(west).
Press
D.
Press D.
Screen: To do this: Do this:
3. Press C to move the flashing in the sequence shown below to select the other
settings.
Seconds
12/24-Hour
Format
Hour Minutes DST
Month Year
City Code
Day Power Saving
Illumination
Duration
Button
Operation Tone
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
E-15
Screen: To do this: Do this:
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone between
(on) and (off)
Toggle the illumination duration between
(approximately 1.5 seconds) and
(approximately 3 seconds).
Toggle between Power Saving on ( ) and
off ( )
Press D.
Use D (+) and B (–).
Use D (+) and B (–).
Press D.
Press D.
Press D.
5. Press A to exit the setting screen.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
E-16
12-hour and 24-hour timekeeping
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
E-17
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C and the DST setting screen appears.
3. Use D to toggle the DST setting on ( ) and off
( ).
• The default DST setting is off ( ).
4. When the setting you want is selected, press A to exit
the setting screen.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
ll
l l l l l ll
ll
ll llll ll
l
DST indicator
E-18
Using the Diving Mode
You can use the Diving Mode to log records of the duration of each of your dives. Each
record includes a log number, the dive time, and the dive start date and time. There is
enough log memory to hold up to 10 dive records. You can use the Log memory Recall
Mode to display dive records currently in log memory (page E-24).
• Hold down C to enter the Diving Mode as shown under “General Guide” on page
E-10.
• If you leave the watch in the Diving Mode for about 11 to 12 hours, it will
automatically switch to the Timekeeping Mode.
E-19
Graphic Area
• The Dive Graph indicates the current dive time in minutes. While a dive time
measurement operation is in progress, the current minute of the dive flashes in the graph.
• The Dive Graph time does not include interval time (page E-20).
Diving Mode Screens
Dive Time Measurement
Reset Screen
llllllll lll
Mode name
llllllll lll
llll lll ll
Current time Dive time (hours,
minutes, seconds)
Ongoing Dive Time
Measurement Screen
Dive start time
Current time Dive time (hours,
minutes, seconds)
Dive Graph