G-Shock GW-225E-7 - Manual

2422-1
Module No. 2422
ABOUT THIS MANUAL
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform operations in each mode. Further details and
technical information can be found in the “REFERENCE” section.
Warning!
Note the following important points concerning Identification Mode data
stored in the memory of this watch.
• The SCUBA diver certificate number and passport number stored
in the memory of this watch can be misused whenever the watch
is in the hands of another party. To protect against the misuse of
the SCUBA diver certificate number and passport number, input
them in coded form that cannot be understood by others.
• Make sure you correctly input your blood type data. Once you
input your blood type, take care that another person does not
wear the watch. Otherwise, emergency medical personnel may
assume that your blood type applies to the person who is
wearing the watch.
• The default blood type screen setting when you first purchase the
watch or after you re-charge the battery after power drops to
Level 5 is “
A ” for the blood type and “ Rh * ” for the Rh factor.
To avoid problems caused by display of the wrong blood type, we
recommend that you input your correct blood type data as soon
as possible after purchasing the watch and whenever you re-
charge the battery after power drops to Level 5.
CASIO COMPUTER CO., LTD. shall not be held liable to you or
any third party for any losses or damages suffered through the
misuse of data stored in the memory of this watch.
Site Mode
Press
C
.
Identification Mode
Alarm Mode
Countdown
Timer Mode Stopwatch Mode
▲
▲
▲ ▲
▲
• Press C to change from mode to mode.
• While in any mode, hold down C for about one second, to enter the
Dive Time Measurement Mode.
• In any mode, press B to illuminate the display.
Dive Time
Measurement
Mode
Hold down
C.
Timekeeping Mode
▲
▲
▲
GENERAL GUIDE
Day of week
Month – Day
PM indicator
Hour : Minutes
Seconds
TIMEKEEPING
Use the Timekeeping Mode to set the current
time and date. You can also view the Dive
Time Measurement Mode log data.
• See the section of this manual that
describes the Dive Time Measurement
Mode for information about log data.
Read This Before You Set the Time and Date!
The times displayed in the Timekeeping Mode and Site Mode are linked.
Because of this, make sure you select a “Home Site” (the site whose time
and date you are setting), before you set the date and time. You can use
any one of the 10 snorkeling and scuba diving sites pre-programmed in
watch memory as the Home Site, or you can create your own.
Important!
If the site you want to use as your Home Site is not in the above list, use
the procedure under “Changing Site Data” to edit the pre-programmed
site data.
Site Name
CAYMAN
GALAPAGOS
GBR
GUAM
HAWAII
JAPAN
MAURITIUS
MALDIVES
RED SEA
TAHITI
GMT Differential
–5.0
–6.0
+10.0
+10.0
–10.0
+9.0
+4.0
+5.0
+2.0
–10.0
Location
Caribbean Ocean
East Pacific Ocean
Coral reef north east of Australia
West Pacific Ocean
Central Pacific Ocean
West Pacific Ocean
East India Ocean
North India Ocean
Red Sea
South Pacific Ocean
To reset the second’s count to zero
1. In the Timekeeping Mode, hold down
A until the second’s digits start
to flash, which indicates the setting screen.
2. Press
D to reset the second’s count to
00 .
• Pressing D while the second’s count is in the range of 30 to 59
resets the seconds to 00 and adds 1 to the minutes. In the range of
00 to 29, the minute’s count is unchanged.
3. Press A to exit the setting screen.
Site name
To set the time and date
1. In the Timekeeping Mode, hold down A
until the second’s digits start to flash, which
indicates the setting screen.
• While the second’s digits are flashing,
press
D to reset the second’s count to
00 .
2. Press
C to move the flashing in the
sequence shown below to select other
settings.
Seconds Hour Minutes
Site
Name
Year
DST
On/Off
12/24-Hour
Format
Month Day
Sleep
Mode
• See “Daylight Saving Time (DST)” for details on DST On/Off setting.
• See “Sleep Mode” for more information about the Sleep Mode.
3. Press
C until the site name is flashing on the display.
4. Use
D to scroll through the site names until the one you want to set
as your Home Site.
• Pressing D scrolls forward, while B scrolls back through site
names.
• See the table for a list of site name.
5. Use
C to move the flashing around the display and select the setting
you want to change.
6. While a setting is flashing, use
D (+) and B (–) to change it.
• When the 12/24-hour setting is flashing, press D to toggle between
12-hour ( 12H ) and 24-hour ( 24H ) timekeeping.
7. Press
A to exit the setting screen.