Lippert Components FT-CG9 - Manual

HAPPIJAC Frame Mount
Camper Tiedown System
Models: FT-UT9 & FT-CG9
IMPORTANT: READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING:
Installation of this camper tiedown system is similar for all truck models. However, while the basic
steps are the same, the details vary from truck to truck Read instructions completely and note correct
installation options at each step for the truck on which tiedown are being installed. These instructions
will show installation of one side only. Both sides install identically.
STEP 1 – [Hardware Kit A] Attach both backing (guide) plates to stabilizer bar. Using
#10 x ¾” sheet metal screws. See diagrams below for specific locations.
Note: The 4 large round holes in guide plate must be to the outer ends of the assembly
at both ends.
1988 & Newer Chev / GMC
1980 – 1998 Ford 1999 & Newer Ford
F-250
(Over 8500 GVW) & F-350
1994 & Newer Dodge Ram
STEP 2 – [Hardware Kit C] Attach frame brace to backing plate by inserting the flat head,
square shouldered plow bolts through the countersunk hole in frame brace and securing
with flat washer, split lock washer and nut. See diagrams below for specific locations.
Note: Do not tighten the nuts at this time. They will be tightened at a later step.
1999 & Newer Ford
F - 250
(Over 8500 GVW) & F- 350
1999 & Newer Chev / GMC
(Silverado / Sierra)
Center Slots Inner Slots
1988 & Newer Chev / GMC
(CK Classic Series Only)
Round Holes
1980 – 1997 Ford
1994 & Newer Dodge
(8500 GVW +)
COMPANY
FRONT ANCHOR INSTALLATION
1
REAR ANCHOR INSTALLATION
NOTE: Rear anchors are installed in the end of the bumper. There is no
precise mounting location since a variety of bumpers may be
installed. The general guidelines are as follows:
1. Mounting location should be as flat & vertical as possible.
2. Be sure no moldings or bumper caps interfere with
the removable coupler.
3. Check back side of selected mounting location to ensure adequate
access for tightening nut.
4. Choose a location as far back as possible from the front edge of bumper
while giving consideration to the other criteria listed above and center
punch and drill a
1 /
8
” pilot hole, then enlarge to 1 /
2
”.
Install Anchor Bolt with 2” fender washer, lock washer & nut.
Flat edges of Anchor Bolt must be horizontal.
Remove
coupler
when not
in use to
prevent loss.
Flats Horizontal
Place well back
From front edge
Of bumper
4
505 N. Kays Drive, Kaysville UT 84037
Phone: (801) 544-2585
Fax: (801) 546-5241
Email: [email protected]
Web Address: www.happijac.com
All defective material must be returned to the factory via prepaid shipment. Upon inspection and determination of claims
warranted, the factory will repair/replace the material at no charge and return the repaired/replaced material to the
customer with delivery charges prepaid by Happijac via common carrier of Happijac's choosing. Upgrades and changes
to shipping mode resulting in additional shipping costs shall be at customers expense.
WARRANTY CLAIMS:
All products manufactured by Happijac Co. are warranted to the retail customer for one year from date of purchase
against defects in material or workmanship. Any defective part(s) will be repaired or replaced (at Happijac’s option)
without charge, when returned transportation prepaid.
There are no other expressed warranties except as set forth above and any implied warranties are limited in duration to
that of the expressed warranty. This warranty does not cover any damage due to misuse, negligence, or accidents. There
is no warranty covering consequential damages, incidental damages, or incidental expenses including damage to
property.
This warranty gives you specific legal rights. You may have other rights which may vary from state to state.
WARRANTY INFORMATION
TERMS OF THE WARRANTY:
ftut9instruct014304