Cambridge Audio Azur 840EW - Manual (Page 9)

840E azur
ENGLISH
9
840E
840W
Output connections - Balanced
The diagram below shows the 840E connected to an 840W using the
Balanced Audio inputs via three-pin XLR connectors.
When using balanced (XLR) connections, the Left and Right Input Type
switches on the 840W must be in the ‘Balanced’ position.
Before making any connections to the loudspeakers, make sure all
power is turned off and only use suitable interconnects (e.g. banana
plugs). Ensure that the positive (+) and negative (-) connections are
matched.
Your loudspeaker may have more than one pair of connecting terminals;
LF (Low Frequency) and HF (High Frequency). For single-wiring it is
recommended to connect to the LF terminals. The metal strip
connecting the low-frequency terminals to the high-frequency terminals
must not be removed (only to be removed for a bi-wiring system).
Note: In this configuration the 840W must be set to Stereo mode.
On Off
Loop Output Input
Balanced Audio - Right Unbalanced
Audio - Right
Input
Loop Output
Input
Loop Output
Out
Control Bus
Trigger
IR Emitter
In
Out/Thru
In
In
Loop Output Input
Balanced Audio - Left Unbalanced Audio - Left
azur 840W Class XD TM Power Amplifier
Power Rating : 230V AC ~ 50Hz
Max Power Consumption : 1600W
www.cambridge-audio.com
Designed in London, England
Power AC
Please ensure that loudspeaker terminals are fully tightened Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
Stereo
Mono
Bi-Amp
Bridged
Loudspeaker Terminals - Right
Impedance 4 - 8 ohms
Bridged
Bridged only!
Please ensure that loudspeaker terminals are fully tightened Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
Loudspeaker Terminals - Left
Impedance 4 - 8 ohms
Bridged only!
Manufactured in an ISO9001 approved facility
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference 2) This device must accept any interference, including interference that may cause undesired operation
N1863
AЯ 46
1 = Ground
2 =
3 =
In Loop
1 = Ground
2 =
3 =
In Loop
Balanced Balanced
Unbalanced
Left
Input Type
Balanced
Unbalanced
Right
Input Type
IMPORTANT! Only change modes when unit is off. Refer to Manual for more information.
Use Left Input for Bridged / Bi-Amp operation.
Mono Mode
Class 2 Wiring Class 2 Wiring
CAUTION
Risk of electric shock. Do not open.
AVIS
Risque de choc electrique. Ne pas ouvrir.
ACHTUNG
Vorm öffnen
des gerätes. Netzstecker ziehen.
R
L
R
L
R
L
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In
Trigger
In Out/Thru In Out
Left Right
Re c Out 2
Sub Out
Re c Out 1 Rec In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Rec Out 2 Rec Out 1 Rec In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1 (Unbalanced) (Unbalanced)
Pre Out
Pre Out Left Right
Balanced Pre Out
Left Right
RS232C
Control Bus
PSU
In
International Patent Pending LeisureTech Electronics Pty Ltd
GND
Power AC
On Off
Power
azur 840E Pre-Amplifier
Power Rating : 230V AC ~ 50Hz
Max Power Consumption : 36W
Designed in London, England
Flat / 200Hz L.P.
Manufactured
in an ISO9001
approved facility This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; 2) This device must accept any interference, including interference that may cause undesired operation.
Input 2 Balanced Audio
Balanced
Unbalanced
Balanced
Unbalanced
Input 1 Balanced Audio
Input 1
Input 2 GND
CAUTION
Risk of electric shock. Do not open.
AVIS
Risque de choc electrique. Ne pas ouvrir.
ACHTUNG
Vorm öffnen
des gerätes. Netzstecker ziehen.
R
L
www.cambridge-audio.com
840E
840W
Output connections - Unbalanced
The 840E features both balanced (XLR) and unbalanced (RCA/Phono)
output connections. For the best quality we recommend you use the
balanced output with power amplifiers that feature this connection
(such as our own 840W Class XD power amplifier).
The diagram below shows the 840E pre-amplifier connected to an Azur
840W power amplifier and a pair of loudspeakers.
When using unbalanced (phono/RCA) connections, the Left and Right
Input Type switches on the 840W must be in the ‘Unbalanced’ position.
Before making any connections to the loudspeakers, make sure all
power is turned off and only use suitable interconnects (e.g. banana
plugs). Ensure that the positive (+) and negative (-) connections are
matched.
Your loudspeaker may have more than one pair of connecting terminals;
LF (Low Frequency) and HF (High Frequency). For single-wiring it is
recommended to connect to the LF terminals. The metal strip
connecting the low-frequency terminals to the high-frequency terminals
must not be removed (only to be removed for a bi-wiring system).
Note: In this configuration the 840W must be set to Stereo mode.
On Off
Loop Output Input
Balanced Audio - Right Unbalanced
Audio - Right
Input
Loop Output
Input
Loop Output
Out
Control Bus
Trigger
IR Emitter
In
Out/Thru
In
In
Loop Output Input
Balanced Audio - Left Unbalanced Audio - Left
azur 840W Class XD TM Power Amplifier
Power Rating : 230V AC ~ 50Hz
Max Power Consumption : 1600W
www.cambridge-audio.com
Designed in London, England
Power AC
Please ensure that loudspeaker terminals are fully tightened Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
Stereo
Mono
Bi-Amp
Bridged
Loudspeaker Terminals - Right Impedance 4 - 8 ohms
Bridged
Bridged only!
Please ensure that loudspeaker terminals are fully tightened Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
Loudspeaker Terminals - Left Impedance 4 - 8 ohms
Bridged only!
Manufactured in an ISO9001 approved facility
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference 2) This device must accept any interference, including interference that may cause undesired operation
N1863
AЯ 46
1 = Ground
2 =
3 =
In Loop
1 = Ground
2 =
3 =
In Loop
Balanced Balanced
Unbalanced
Left Input Type
Balanced
Unbalanced
Right Input Type
IMPORTANT! Only change modes when unit is off. Refer to Manual for more information.
Use Left Input for Bridged / Bi-Amp operation.
Mono Mode
Class 2 Wiring Class 2 Wiring
CAUTION
Risk of electric shock. Do not open.
AVIS
Risque de choc electrique. Ne pas ouvrir.
ACHTUNG
Vorm öffnen
des gerätes. Netzstecker ziehen.
R
L
R
L
R
L
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In
Trigger
In Out/Thru In Out
Left Right
Re c Out 2
Sub Out
Re c Out 1 Rec In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Rec Out 2 Rec Out 1 Rec In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1 (Unbalanced) (Unbalanced)
Pre Out
Pre Out Left Right
Balanced Pre Out
Left Right
RS232C
Control Bus
PSU
In
International Patent Pending LeisureTech Electronics Pty Ltd
GND
Power AC
On Off
Power
azur 840E Pre-Amplifier
Power Rating : 230V AC ~ 50Hz
Max Power Consumption : 36W
Designed in London, England
Flat / 200Hz L.P.
Manufactured
in an ISO9001
approved facility This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; 2) This device must accept any interference, including interference that may cause undesired operation.
Input 2 Balanced Audio
Balanced
Unbalanced
Balanced
Unbalanced
Input 1 Balanced Audio
Input 1
Input 2 GND
CAUTION
Risk of electric shock. Do not open.
AVIS
Risque de choc electrique. Ne pas ouvrir.
ACHTUNG
Vorm öffnen
des gerätes. Netzstecker ziehen.
R
L
www.cambridge-audio.com